York YVAG012 Скачать руководство пользователя страница 11

Страница: 11 / 56

FORM NO.:

6U5M-A11M-N

JOHNSON CONTROLS

LOCATION

These units are designed for outdoor installations on

ground level, rooftop, balcony, and any other place that

is suitable for installation with reliable load bearing.

Location should be selected for minimum sun exposure

and away from boiler flues and other sources of

airborne corrosive or flammable gas that could attack

the ambient coils and steel parts of the unit. The units

must be installed with sufficient clearances for air

entrance to the condenser coil to ensure adequate

supply of fresh air, for air discharge away from the

condenser, and for servicing access.

If the units are located at a place where unauthorized

personnel could reach, isolation security measures shall

be taken, such as setting protective guard, to avoid

human sabotage and prevent the control cabinet from

being opened and the operating electrical component

from being exposed;

The highest point of the air conditioning system shall

not be 20m over the unit (for 20m higher, please consult

YORK Company);

In installations where winter operation is intended and

snow accumulations are expected, additional height

must be provided to ensure normal condenser air flow.

For places with special installation

requirements, please consult to the

building contractor or the architect and

designer or other professionals.

Noise Sensitive Locations

Efforts should be made to assure that the unit is not

located next to occupied spaces or noise sensitive areas

where unit noise level would be a problem.

Please make the unit face the place that is sensitive to

noise as far as possible to reduce the influence of

operating noise of the unit;

If the heat exchanger part is without block, protective

baffle plate can be added to reduce the influence of

operating noise of the unit.

Cold Climate Locations

If the unit is operating in low ambient temperature, be

sure to follow the instructions listed below.

1. A baffle plate installed on the airside of the unit is

recommended to prevent exposure to snow in winter.

2. In areas with large snow precipitation, make sure

the coil and fan will not be affected by the snow.

Construct a lateral canopy if necessary.

3. Deice before operating if the fan blades fail to

rotate after long time standby in snow.

FOUNDATION

The unit should be mounted on a flat and level

foundation, floor, or rooftop capable of supporting the

entire operating weight of the equipment. See

PHYSICAL DATA for operating weight. If the unit is

elevated beyond the normal reach of service personnel,

a suitable catwalk must be capable of supporting

service

personnel,

their

equipment,

and

the

compressors.

To ensure the outdoor unit is placed flat on the base, the

outdoor unit must be placed after confirming the plane

where the outdoor unit would be placed is even. After

the installation of the outdoor unit the outdoor unit shall

be examined whether it is leveled, and the angle of

inclination shall be smaller than 10°; for a unit with an

absorber, the level inspection shall be installed after the

installation of absorber;

There are installing holes on the foundation of the unit,

and they can be used to closely connect the unit and the

foundation;

Ground location

For the ground installation, the steel foundation of the

unit shall be placed on smooth and flat concrete

foundation. DO NOT connect the unit foundation with

the building foundation for fear that noise and vibration

would be transmitted;

Cooke Industries - Phone: +64 9 579 2185 Email: [email protected] Web: www.cookeindustries.co.nz

Содержание YVAG012

























































Результаты поиска

Содержание YVAG012

Отзывы:

Похожие инструкции для YVAG012

Бренды по названию

Популярные бренды

York YVAG012, Руководство по эксплуатации и техническому обслуживанию

Результаты поиска

Содержание YVAG012

Отзывы:

Похожие инструкции для YVAG012

Бренды по названию

Популярные бренды