York YR Скачать руководство пользователя страница 46

Страница: 46 / 110

JOHNSON CONTROLS

FORM 160.81-O1 (1020)

ISSUE DATE 10/05/2020

SECTION 2 - OPTIVIEW™ CONTROL CENTER

Optiview Control Center

GROUND FAULT PROTECTION SCREEN

Overview

With software version C.MLM.05.06.xxx (and later)

or C.OPT.05.06.xxx (and later), this screen is used to

clear a “Motor – Ground Fault” safety shutdown. With

these and later software versions, an ADMIN password

is required to clear this fault and restart the chiller. This

is to prevent the severe compressor/motor damage that

could occur from initiating chiller starts after this fault

has occurred. To prevent restarting the chiller until the

motor condition can be evaluated by a qualified ser-

vice technician, the chiller cannot be started until the

Ground Fault contacts (TB3-71) open and the service

technician obtains an ADMIN password from YORK

and performs a special reset procedure listed in OptiV-

iew Control Center Service Instructions (Form 160.81-

M1).

The ADMIN password must be obtained

from YORK. Service Technicians refer to

OptiView Control Center Service Instruc

tions (Form 160.81-M1).

Display Only

Motor Run (LED)

Illuminates when the compressor motor is being com-

manded to run.

FIGURE 15 - GROUND FAULT PROTECTION SCREEN

LD11549

Motor Ground Fault Switch (LED)

Illuminates when a motor Ground Fault safety shut-

down is in effect.

Motor Current % Full Load Amps

Displays the motor current as a percentage of full load

amps (FLA).

Voltage Phase A, B and C

Displays the 3-phase input line voltage measured by

the Solid State Starter.

Current – Phase A, B and C

Displays the 3-phase motor current values measured

by the Solid State Starter.

Programmable

Fault Acknowledge

Access Level Required:

ADMIN

This key is only displayed if a “Motor – Ground Fault”

condition is in effect. It is used to perform the special

reset procedure required to clear the “Motor – Ground

Fault” fault and restart the chiller.

Software version C.MLM.05.06.xxx (and later) and C.OPT.05.06.xxx (and later)

Содержание YR















































































































Результаты поиска

Содержание YR

Отзывы:

York YR, Руководство пользователя, Страница: 46 / 110

Результаты поиска

Содержание YR

Отзывы: