manualshive.com logo in svg

York YR, Руководство пользователя, Страница: 16 / 110

Поделиться
Скачать
York YR Скачать руководство пользователя страница 16

JOHNSON CONTROLS

16

FORM 160.81-O1 (1020) 

ISSUE DATE 10/05/2020

SECTION 1 - DESCRIPTION OF SYSTEM AND FUNDAMENTALS OF OPERATION

•  With software version C.OPT.05.08.303 (and ear-

lier), it is 60 seconds. 

•  With software version C.OPT.05.09.303 (and later), 

the duration is determined by the motor current 

when the shutdown command is received as follows: 

-  100% FLA or above equals 30 seconds.
-   75% FLA and below equals 5 seconds, lin-

ear between 75% and 100% FLA. 

In multiple chiller applications it may be possible for 

the chilled liquid (Water or Brine) from an operating 

chiller to flow through the Evaporator of a standby 

chiller. This represents a possible freeze threat to the 

Condenser of the standby chiller. The 

Standby Chiller 

Freeze Protection

 feature minimizes this freeze po-

tential by allowing the OptiView™ Control Center of 

the standby chiller to cycle the condenser pump based 

on the standby chiller’s Condenser Saturation Tem-

perature while it is shutdown. At chiller shutdown, the 

pump runs until the condenser saturation temperature 

increases to more than 35.0ºF, whereupon the pump is 

turned OFF. While the chiller is shutdown, the condens-

er saturation temperature is monitored. If it decreases 

to less than 30.0ºF, the pump is turned ON and runs un-

til the temperature increases to more than 35.0ºF. After 

the chiller has been shutdown for at least the time delay 

programmed as the Freeze time setpoint, and the tem-

perature decreases to less than 28.0ºF, “WARNING – 

FREEZE THREAT FROM OPERATING CHILLER” 

is displayed and alarm output is activated. When the 

temperature increases to 28.0ºF, the warning message 

and alarm output automatically clear. If this feature is 

desired, Freeze Warning must be enabled by a Service 

Technician. A complete description of this feature is 

contained in the OptiView Control Center Service In-

structions (Form 160.81-M1).

Motor current overload protection is provided by the 

CM-2 Board (Electro-Mechanical Starters) and Liq-

uid Cooled Solid State Starter. The overload is a timed 

function beginning at 105% of the Chiller Full Load 

Amps. With software version C.OPT.05.07.xxx (and 

later), there is also a motor current overload provided 

by the Microboard software. It also starts at 105% of 

the chiller Full Load Amps and is adjustable over the 

range of 12 (default) to 40 seconds with the 105% Mo-

tor Current Time setpoint. When the motor current has 

exceeded 105% of Chiller FLA continuously for the 

programmed time period, a safety shutdown is per-

formed and “105% Motor Current Overload” is dis-

played on the System Details Line of the Display. 
The coolant temperature inside any JCI-supplied 

liquid-cooled motor starter must be maintained 

above  the dewpoint temperature in the equipment 

room to prevent condensing water vapor inside the 

starter cabinet. Therefore, an additional temperature-

controlled throttle valve is needed in the flow path 

for the starter heat exchanger to regulate cooling 

above the equipment room dewpoint for applica-

tions using cooling sources other than evaporative 

air-exchange methods, such as wells, bodies of wa-

ter, and chilled water. The temperature control valve 

should be the type to open on increasing drive cool-

ant temperature, fail-closed, and set for a tempera-

ture above dewpoint. It can be requested as factory- 

supplied on a chiller order by special quotation.

Содержание YR















































































































Отзывы:

Нет отзывов