manualshive.com logo in svg

York YDAJ87KU6, Руководство пользователя

Поделиться
Скачать
York YDAJ87KU6 Скачать руководство пользователя страница 85

FORM 150.75-NM2

85

YORK INTERNATIONAL

When the Low Ambient Option is installed, the following

physical changes are made to the standard chiller:

1. Discharge pressure transducers and wiring are added

to both modules.

2. Reversing contactors 9M, 10M, 15M and 16M with

supporting wiring are added to both the Master and

Slave Control Panels.

3. A second Relay Output Board and wiring is installed

in both Control Panels.

Programming

The control panel may be programmed for “AMBIENT

& DISCH PR FAN CONTROL” (Ambient & discharge

pressure fan control) or by “DISCHARGE PRESSURE

FAN CONTROL” (fan control by discharge pressure

only). This is selected by placing SW8 on both the Mas-

ter and Slave Microprocessor Boards to the appropri-

ate position. See page 40.

SW2 on each microprocessor board must also be pro-

grammed for “LOW AMBIENT CONTROL” to allow

operation at temperatures below 25°F. To accomplish

this, place SW2 in the CLOSED position. See page 39.

After the switch is properly positioned, the OUTSIDE

AIR TMP LOW CUT-OUT in the PROGRAM mode can

then be programmed between 0° - 25°F. See page 46.

NOTE: For operation below 0°F, program the cut-out

for 0°F. This will cause the microprocessor to

ignore the low ambient cut-out regardless of

temperature.

Operation of the fans will be discussed in both “Ambi-

ent and Pressure Control” as well as “Pressure Only”

control in the following text.

Ambient and Pressure Fan Control

0°F - 25°F

Fan operation on each system below 25°F is controlled

only by the discharge pressure of the respective sys-

tem. Each system will operate 4 steps of fan control as

follows:

1. Until discharge pressure reaches 320 PSIG, the fans

will be completely off.

2. The second stage of fan control will energize fans 1

& 3 (SYS 1, 9M and 10M), fans 5 & 7 (SYS 2, 15M

&16M), fans 9 & 11 (SYS 3, 9M and 10M)  or fans 13

& 15 (SYS 4, 15M & 16M) in the reverse direction

when the discharge pressure exceeds 320 PSIG.

Once the reversing contactors are energized, they

will stay on until the discharge pressure of the sys-

tem falls below 120 PSIG, the ambient temperature

exceeds 35°F, or discharge pressure of the system

rises above 340 PSIG.

NOTE: The corresponding compressor must be on

for a minimum of 4 sec. before the reversing

fans are permitted to start.

3. The third stage of fan control will energize fans 2 & 4

(SYS 1, 6M & 8M), fans 6 & 8 (SYS 2, 12M & 14M),

fans 10 & 12 (SYS 3, 6M and 8M) or fans 14 & 16

(SYS 4, 12M & 14M) as well as turn off the reversing

fans on the respective system whenever discharge

pressure exceeds 340 PSIG. These fans will stay on

until discharge pressure drops below 120 PSIG.

NOTE: The corresponding compressor must be on

for 4 sec. before these fans are permitted to

start.

4. The fourth stage of fan control will energize fans 1 &

3 (SYS 1, 5M & 7M) or fans 5 & 7 (SYS 2, 11M &

13M), fans 9 & 11 (SYS 3, 5M & 7M) and fans 13 &

15 (SYS 4, 11M & 13M) and will operate the corre-

sponding fans in the forward direction whenever dis-

charge pressure exceeds 360 PSIG. These fans will

stay on until discharge pressure drops below 140

PSIG.

NOTE: The corresponding compressor must be on for

4 sec. before these fans are permitted to start.

Ambient and Pressure Fan Control

25° - 45°F

Fan control between 25°and 35°F is controlled by dis-

charge pressure. If the reversing fans are on, the revers-

ing fan will continue to operate until the temperature

reaches 35°F or discharge pressure reaches 340 PSIG.

At 35°F or 340 PSIG, fans 2 & 4 (SYS 1, 6M & 8M), fans

6 & 8 (SYS 2, 12M & 14M), or fans 10 & 12 (SYS 3, 6M

& 8M) or fans 14 & 16 (SYS 4, 12M & 14M) will energize.

Between 25°F and 45°F if the reversing fan is not oper-

ating, after 4 seconds of compressor operation, fans 2 &

4 (SYS 1), fans 6 & 8 (SYS 2), fans 10 & 12 (SYS 3) or

fans 14 & 16 (SYS 4) will energize. This is identical to

standard fan control by temperature (Page 82). No pres-

sure override exists. If temperature drops below 25°F,

these fans will remain on until cycled off by pressure.

Ambient and Pressure Fan Control

45°F and Higher

Fan control above 45°F is strictly controlled by tempera-

ture with no pressure override.

After 4 seconds of operation, fans 2 & 4 (SYS 1, 6M &

8M), fans 6 & 8 (SYS 2, 12M & 14M), fans 10 & 12

(SYS 3, 6M & 8M) or fans 14 & 16 (SYS 4, 12M & 14M)

will energize turning the fans in the forward direction.

Содержание YDAJ87KU6





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды