York YDAJ87KU6 Скачать руководство пользователя

Страница: 32 / 100

YORK INTERNATIONAL

UNIT CONTROLS AND OPERATION

YORK MICROCOMPUTER CONTROL CENTER

26572A

FIG. 21

MICROCOMPUTER CONTROL CENTER

INTRODUCTION

The YORK MicroComputer Control Center is a micro-

processor based control system capable of multi-cir-

cuit control to maintain chilled liquid temperature. The

chiller system is controlled by two control / power pan-

els in a Master / Slave configuration. The Master is rec-

ognized by the attached operator display and keypad

which provides control from a single operator location.

A 40 character display (2 lines of 20 characters) allows

the operator to display system operating parameters

as well as access programmed information already in

memory. On the Master Control Panel, a keypad for

programming and accessing setpoints, pressures, tem-

peratures, motor current, cut-outs, daily schedule, op-

tions, and fault information is provided. No Control Panel

is present on the Slave Panel.

A master ON / OFF switch is available to activate or

de-activate the chiller system. Separate system (SYS)

switches for each refrigerant system (up to 4) are pro-

vided on each Microprocessor Board.

Remote cycling, unloading, and chilled water tempera-

ture reset can be accomplished by used supplied dry

contacts.

Compressor starting / stopping and loading / unloading

decisions are performed by the Microprocessor to main-

tain leaving water temperature. These decisions are a

function of temperature deviation from setpoint and rate

of change of temperature.

MICROPROCESSOR BOARD

The Microprocessor Boards are the controller and de-

cision makers in the control panels. System inputs from

pressure transducers, temperature sensors, and C.T.s

are connected directly to the Microprocessor Board. The

Microprocessor Board circuitry multiplexes these ana-

log inputs, digitizes them, and constantly scans them to

keep a constant watch on the chiller operating condi-

tions. From this information, the Microprocessor then

issues commands to the Relay Output Board to control

contactors, solenoids, etc. for water temperature con-

trol and to react to safety conditions.

Two Microprocessor Boards, one acting as a master

and one as a slave controller are present in the chiller.

Control and programming for the entire chiller is pro-

vided by the Master Microprocessor Board. The mas-

ter also has direct control of compressor 1 and 2. The

Slave Microprocessor Board is responsible for direct

control of compressor 3 and 4 as dictated by the

Masters requirements. Communications and informa-

tion transmission between the two micros is accom-

plished by a 2 wire RS-485 communications link.

Keypad commands are acted upon by the micro to

change setpoints, cut-outs, scheduling, operating re-

quirements, and to provide displays.

Содержание YDAJ87KU6





































































































Результаты поиска

Содержание YDAJ87KU6

Отзывы:

Похожие инструкции для YDAJ87KU6

Бренды по названию

Популярные бренды

York YDAJ87KU6, Руководство пользователя

Результаты поиска

Содержание YDAJ87KU6

Отзывы:

Похожие инструкции для YDAJ87KU6

Бренды по названию

Популярные бренды