manualshive.com logo in svg

York D835, Руководство пользователя, Страница: 9 / 78

Поделиться
Скачать
York D835 Скачать руководство пользователя страница 9

Safety

 CONTROL THE IGNITION SOURCE

 

a

 

   Apply a “no smoking” policy in all 

potentially hazardous areas.

 

b

 

   Use only  explosion-proof lights.

 

c

 

   All welding and cutting is to take place 

on the outside of the facility.

 

d

 

   Properly lubricate bearings on all 

equipment at the required intervals.

 

e

 

   Use magnets to trap metal that might be 

mixed in with the grain.

 

f

 

   Check the lagging on bucket elevator 

belt pulleys and belt conveyor pulleys 

and replace lagging if any lagging is 

worn or smooth.

 

g

 

   Use recommended safety devices 

such as  heat detectors on bearings, 

 motion sensors on the boot shaft,  belt 

alignment sensors, or  limit switches 

to shut down the system if the leg is 

choked. Make certain all electrical 

wiring,  lights, and outlets meet local 

 codes. (

DANGER! Do not “jog” a 

choked leg.

)

 GRAIN DUST EXPLOSION MYTHS

Throughout the years several myths have 

surrounded grain dust explosions. These are 

some of the most common:

 

a

 

   Grain dust explosions do not occur in 

times of high humidity.

False

: Dust explosions have occurred 

during rain storms.

 

b

 

   Grain dust explosions do not occur in 

wooden elevators. 

False

 

c

 

   Grain dust explosions do not occur in 

small country elevators.

False

: 70% - 80% of grain elevator 

explosions occur in small country 

terminals.

 

d

 

   There are only (2) explosions that occur, 

a primary and a secondary.

False

: Up to (13) explosions have been 

documented during (1) incident.

 EXPLOSION  VENTING

Explosion vents for the trunking can be supplied 

as optional equipment for all models of bucket 

elevators.  Explosion vents for heads are standard 

on all SC models and optional on smaller units. 

These vents, should an explosion occur within 

a leg, may possibly minimize damage to the leg 

and prevent a secondary explosion.

  WARNING!  

ALL INFORMATION ON THIS PAGE IS 

WARNING INFORMATION!

control the ignition source           pulleys

grain dust explosion myths

explosion venting

explosion-proof lights

welding

cutting

bearings

magnets

lagging

heat detectors

motion sensors

limit switches

electrical

electrical wiring

codes

9

GLOBAL

INDUSTRIES, INC.

Drag Conveyors 

  10230011

2016-06-14

Содержание D835















































































Отзывы:

Нет отзывов