manualshive.com logo in svg

York D835, Руководство пользователя, Страница: 28 / 78

Поделиться
Скачать
York D835 Скачать руководство пользователя страница 28

Assembly

Intermediate Sections

 

2 

bolt intermediate sides to bottom

If the conveyor was not assembled when it 

came, start intermediate section assembly 

by bolting the intermediate sides to the 

intermediate bottom. Use 3/8” x 1” bin bolts 

and flange nuts. When doing so, make certain 

the bottom has the correct offset (see below) 

from the sides. This offset is made up at the 

conveyor head and tail ends. Before tightening 

the sides to the bottom make certain the sides 

are square and parallel to each other. Leave 

out the end bolts and use a drift pin so the rows 

of bottom holes will align. Torque the nuts at 

44 ft-lb [59.66 N•m or 6.08 kgf-m].

NOTE: The model ID1275 intermediate section 

is 

shown in the example below

.

Exploded View 

with idlers

COVER

3/8” FLANGE NUT

SPLICE 

ANGLE

LINERS

IDLER

5/16” 

LOCK 

WASHER

5/16” x 1” 

BIN BOLT

3/8” FLANGE NUT

3/8” HEX BOLT

3/8” COUNTERSINK BOLT

SIDE

BOTTOM

use 1/4” countersink

bolts and flange nuts here

1/4” FLANGE NUT

Side View

head

tail

2” [51 mm] gap

2” [51 mm] extension

INTERMEDIATE SECTION

28

GLOBAL

INDUSTRIES, INC.

Drag Conveyors 

  10230011

2016-06-14

Содержание D835















































































Отзывы:

Нет отзывов