manualshive.com logo in svg

York D835, Руководство пользователя, Страница: 2 / 78

Поделиться
Скачать
York D835 Скачать руководство пользователя страница 2

2

GLOBAL

INDUSTRIES, INC.

Drag Conveyors 

  10230011

2016-06-14

The Symbol 

shown below

 is used to call your attention to instructions 

concerning your personal safety. Watch this symbol - it points out 

important safety precautions. It means “ATTENTION” - Become 

Alert! Your Personal Safety Is Involved! Read the message that 

follows and be alert to the possibility of personal injury or death.

    Your 

Personal 

Safety Is Involved

A copy of this manual should be available at all times to the owner/operator. Additional 

copies may be requested from the company at the address shown on the back cover. 

Please reference manual part number 

10230011

 when requesting additional copies.

 

Please Contact BROWNIE SYSTEMS or Your Dealer 

 

If You Have Any Questions Concerning This Manual

Keep This Manual In A Safe Place Available For Future Reference.

Be Alert!

kas001-1_2013-03-29

The safety and performance of this 

Drag Conveyor

, constructed and readied 

for operation will be affected by the installation and construction personnel. 

Drag Conveyor installation can

 involve extreme heights and high winds. 

Careful consideration must be given to the structural requirements. 

We 

therefore highly recommend the use of a skilled construction company with a 

qualified structural 

engineer.

 

MFS/YORK/STORMOR

 cannot be responsible 

for the construction of the 

Drag Conveyor

. The information obtained in 

this manual is offered only as a convenience to the installer. No liability is 

expressed or implied toward the installation.

kas001-2_2012-12-03

Содержание D835















































































Отзывы:

Нет отзывов