manualshive.com logo in svg

York D835, Руководство пользователя, Страница: 25 / 78

Поделиться
Скачать
York D835 Скачать руководство пользователя страница 25

Pre-Installation Preparation

Before starting conveyor installation, 

study 

this entire manual

 and any other applicable 

documents, including, but not limited to, OSHA 

regulations and the National Electric Code. 

Distribute the parts in an orderly fashion at the 

construction site to facilitate later assembly.

Receiving Inspection

The conveyor has been carefully checked before 

shipment. Carefully inspect the shipment and 

all components. Use the packing list provided 

with the shipment to verify that all parts have 

been received. Any discrepancies should be 

clarified immediately. Please remember that any 

damaged or missing parts must be noted on the 

bill of lading at the time of delivery. Report any 

damage or shortage to the delivering carrier 

as soon as possible. MFS/YORK/STORMOR’s 

responsibility for damage to the equipment ends 

with acceptance by the delivering carrier.

Pre-Assembly

Bolt Head Identification

Grade 2

Grade 5

Grade 8

Grade 8.2

Bolt

Diameter 

-

Threads/Inch

Grade 2

Grade 5

Grade 8 and 8.2

P

T

P

T

P

T

ft-lb

Nm

kgf-m

ft-lb

Nm

kgf-m

ft-lb

Nm

kgf-m

1/4” 

- 20

1313

6

8.1

0.83

2000

9

12

1.2

2850

13

18

1.8

5/16” 

- 18

2176

12

16

1.7

3350

19

26

2.6

4700

27

37

3.7

3/8” 

- 16

3188

22

30

3.0

4950

34

46

4.7

6950

48

65

6.6

7/16” 

- 14

4388

35

47

4.8

6800

55

75

7.6

9600

77

104

11

1/2” 

- 13

6850

63

85

8.7

9050

83

110

11

12800

120

163

17

5/8” 

- 11

9300

110

150

15

14500

170

230

24

20300

230

312

32

3/4” 

- 10

11400

160

217

22

21300

290

390

40

30100

410

556

57

7/8” 

- 9

13800

220

298

30

29500

470

640

65

41600

670

910

93

1” 

- 8

15000

280

380

39

38700

710

960

98

54600

1000

1400

138

coarse thread bolts

Bolt Torque Values

Use the torque values listed in the table above for all drag conveyor 

connections!

Bolt Torque

25

GLOBAL

INDUSTRIES, INC.

Drag Conveyors 

  10230011

2016-06-14

Содержание D835















































































Отзывы:

Нет отзывов