manualshive.com logo in svg

York D835, Руководство пользователя, Страница: 33 / 78

Поделиться
Скачать
York D835 Скачать руководство пользователя страница 33

Assembly

33

GLOBAL

INDUSTRIES, INC.

Drag Conveyors 

  10230011

2016-06-14

NOTE: The chain sections in 

examples b and c

 are shown as 

though they were on the flow side 

and viewed from above. 

Optional Carry-Back Cups

 

6 

Optional carry-back cups

Install the carry-back cups 

as shown

 in 

examples a - c

. Use the paddle bolts, nuts, 

and lock washers. The carry back cup bolts 

to the UHMW paddle; it does not bolt to the 

attachment. You may stagger the cups 

as 

shown

 in option #1 or option #2.

Instructions

When intermediate discharges are used, some 

carry-over of the conveying material results. 

The term carry-over refers to the few kernels 

of grain which ride across the intermediate 

discharges on the chain assembly. The 

amount of carry-over is approximately (1/10) of 

(1) percent of the conveyed material.

When there is no gate mechanism at the final 

discharge, the carry-over is simply discharged. 

If mixing of grain is not desired, YORK advises 

installing a gate at the final discharge and 

carry-back cups on every other paddle.

CARRY-BACK 

CUP

UHMW PADDLE

ATTACHMENT

PADDLE 

BOLTS, NUTS, and 

LOCK WASHERS

toward head

b) Cup Stagger Option #1

INTERMEDIATE SECTION BOTTOM

UHMW PADDLE

ATTACHMENT

CHAIN

CARRY-BACK CUP

a) Carry Back Cup Side View

toward head

CARRY-BACK CUP

UHMW PADDLE

ATTACHMENT

PADDLE BOLTS, 

NUTS, and 

LOCK WASHERS

c) Cup Stagger Option #2

Содержание D835















































































Отзывы:

Нет отзывов