York International ZQ Series Скачать руководство пользователя страница 12

Страница: 12 / 92

4. For ground level installation, use a level

concrete slab with a minimum thickness of 4

in. The length and width should be at least 6

in. greater than the unit base rails. Do not tie

slab to the building foundation.

5. Roof structures must be able to support the

weight of the unit and its options/accessories.

Unit must be installed on a solid, level roof

curb or appropriate angle iron frame.

6. Maintain level tolerance to 1/2 in. across the

entire width and length of unit.

WARNING

Excessive exposure of this furnace to contaminated

combustion air will result in safety and performance

related problems. Typical contaminates include:

permanent wave solution, chlorinated waxes and

cleaners, chlorine based swimming pool chemicals,

water softening chemicals, de-icing salts or chemicals,

carbon tetrachloride, Halogen type refrigerants,

cleaning solvents (e.g. perchloroethylene), printing

inks, paint removers, varnishes, hydrochloric acid,

cements and glues, anti-static fabric softeners for

clothes dryers, masonry acid washing materials.

Clearances

All units require particular clearances for proper

operation and service. Installer must make

provisions for adequate combustion and ventilation

air in accordance with section 5.3 of Air for

Combustion and Ventilation of the National Fuel

Gas Code, ANSI Z223.1 – Latest Edition (in U.S.A.),

or Sections 7.2, 7.3, or 7.4 of Gas Installation

Codes, CSA-B149.1 (in Canada) - Latest Edition,

and/or applicable provisions of the local building

codes. Refer to Table 4 for clearances required for

combustible construction, servicing, and proper unit

operation.

WARNING

Do not permit overhanging structures or shrubs to

obstruct condenser air discharge outlet, combustion

air inlet or vent outlets.

Rigging And Handling

Exercise care when moving the unit. Do not remove

any packaging until the unit is near the place of

installation. Rig the unit by attaching chain or cable

slings to the lifting holes provided in the base rails.

Spreader bars, whose length exceeds the largest

dimension across the unit,

MUST

be used across the

top of the unit.

CAUTION

If a unit is to be installed on a roof curb other than a

Ducted Systems roof curb, gasketing must be applied

to all surfaces that come in contact with the unit

underside.

CAUTION

Before lifting, make sure the unit weight is distributed

equally on the rigging cables so it will lift evenly.

Units may be moved or lifted with a forklift. Slotted

openings in the base rails are provided for this

purpose.

LENGTH OF FORKS MUST BE A MINIMUM OF 60

INCHES.

CAUTION

All panels must be secured in place when the unit is

lifted.
The condenser coils should be protected from rigging

cable damage with plywood or other suitable material.

INSTALLATION MANUAL ZQ SERIES 3 - 5 ton 60 Hertz R-410A

Johnson Controls Ducted Systems

Содержание ZQ Series




























































































Результаты поиска

Содержание ZQ Series

Отзывы:

Похожие инструкции для ZQ Series

Бренды по названию

Популярные бренды

York International ZQ Series, Руководство по установке

Результаты поиска

Содержание ZQ Series

Отзывы:

Похожие инструкции для ZQ Series

Бренды по названию

Популярные бренды