background image

 

Manual Change for IM 01G05B03-01E 1st Edition : No.15-010-E  July 30 2015-00

 

 

 

 

 

 

 

 

 

This is the supplement for the original manual (No. IM 01G05B03-01E, 1st Edition) regarding the added and changed 

items. Please also refer to this supplement when you read the manual. 

 

 

Addition to the section “3.5.4 Connection of the Transducers” (page 18) : 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(3) Grounding 

The connection of the cable shield will be realized as shown in the drawing below after going through the 

procedures (1) and (2) in the above. Connect the main unit to the ground through the terminal “PE” of the power 

supply terminals in the main unit. The grounding resistance should be less than 100 ohm. 

 

 

 

 

 

 

 

 

 

  (4) Connecting the Sensor ROMs 

Connect the sensor ROMs to the corresponding terminals in the main unit when connecting transducers. The 

sensor ROMs are packed and affixed to the transducers when shipped from the factory. 

Manual Change

No. 15-010-E

User’s 
Manual 

US300FM 
Ultrasonic Flowmeter

Unit : mm

(a) Main unit side

(b) Junction box side

Thin lines

(**)

Shield line

Cable
shield

(meshed)

7

±

2

13

±

3

60

±

5

52

±

5

10

±

3

7

±

2

Brown 

(*)

White

White

Perform
soldering

(*) 

Finish the brown cables as well as white cables.

(**) 

You do not connect the thin lines to any terminals.

Brown 

(*)

12

±

2

Less

than

10mm

12

±

2

Perform
soldering

Shield line

Cable
shield

(meshed)

Thin lines

(**)

Less

than

5mm

(1) Cable Finish 

The cable finish should be done as the drawings (a) and (b) 

shown in the right. 

 

 

 

(2) Cable Gland 

When tightening the gland, not only pull back the cable shield 

(meshed part) but also roll it out into a ring-shaped form and let 

it be pushed by the compression part (grey-colored plastic) so 

that the cable shield will have electrical contact with the gland 

body. Also, be sure to align the convexity part outside the 

compression part and the concavity part inside the gland body.

Refer to the drawings below. 

Gland body

Compression

part

Rubber ring

Cable shield
(ringed-shape)

Outer skin of the cable

Signal lines

Cap nut

Cutaway view of the cable gland

Outer wall of
the main unit
or junction box

Gland body 
(concavity part inside) 

Cable shield rolled out into a ring-shaped form

Compression part   
(convexity part outside) 

Components of the cable gland 

Grounding resistance 
less than 100 ohm 

GND

Sensors

Junction box

Main

unit

Transducers

Connection

cable

Connection of the cable shield

 

Yokogawa Electric Corporation 

Содержание US300FM













Отзывы: