YOKOGAWA TB830D Скачать руководство пользователя страница 79

Страница: 79 / 85

<APPENDIX>

App.-2

IM 12E01B30-02EN

1st Edition : Mar. 08, 2023-00

4: After the cleaning time elapses, SV4 opens during the Drainage time to wash the Flow cell,

head tank, and the pipes between head tank and the detector.

5: If “Repeat count of wash” is set to over 2, valve working 2 to 4 is repeated. Right before the

last draining, SV3 closes and the zero water stops.

6: Once the draining for cleaning completes, SV4 closes, SV1 opens, and TB830D starts

feeding a sample.

7: After Flow/Calibration Waiting time” elapses, the detector becomes Recovery time.
8: Afthe the Recovery time elapses, a measurement starts.

Automatic calibration (-A3, -A5)

OPEN

Drainage time

Washing time

Flow/Calibration

Waiting time

Calibration

time

Flow/Calibration

Waiting time

Flow/Calibration

Waiting time

Recovery time

Washing

Calibration

Recovery Meas.

Washing time

Flow/Calibration

Waiting time

Meas.

Status

SV1(Sample)

SV2(Wash. water)

SV3(Zero)

SV4(Drain)

1: When sequence starts, Automatic cleaning works first. After the Automatic cleaning, an

automatic calibration starts without a recovery time. Therefore, the steps from 1 to 5 for

“Automatic cleaning (-A3)” are common. When a Drainage time starts after the last Cleaning

time, the screen shows a calibration. This time, SV3 (Zero) stays open.

2: After the Drainage time elapses, SV4 closes and a zero water starts flowing into the

detector.

3: After “Flow/Calibration Waiting time” elapses, a zero calibration starts. The calibration

time in the figure shows the total amount of time of an Auto stabilization check and a zero

calibration which is carried out after the Auto stabilization check (the reading becomes

stable).

4: After the calibration, SV4 opens and the zero water in the Flow cell is drained.
5: After the Drainage time elapses, SV4 closes, SV1 opens, and a sample starts flowing into

the detector.

6: After Flow/Calibration Waiting time elapses, TB830D starts the Recovery time.
7: After the Recovery time elapses, a measurement starts.

Содержание TB830D






















































































Результаты поиска

Содержание TB830D

Отзывы:

YOKOGAWA TB830D, Руководство пользователя, Страница: 79 / 85

Результаты поиска

Содержание TB830D

Отзывы: