manualshive.com logo in svg

YOKOGAWA TB830D, Руководство пользователя, Страница: 14 / 85

Поделиться
Скачать
YOKOGAWA TB830D Скачать руководство пользователя страница 14

  

<2.  INSTALLATION, PIPING, AND WIRING>

2-1

IM 12B01B30-02EN

1st Edition : Mar. 08, 2023-00

2.  INSTALLATION, PIPING, AND WIRING

The “TB830D Surface Scattering Turbidity Detector” is shipped after being fully packaged so that 

it will not be damaged during transportation. Unpack carefully near the installation location.
The TB830D may also be shipped embedded in a Sampling system.

n

  Installation Location

The TB830D should be installed in a location:

•  In a building or a cabinet where no direct sunlight or rainwater can get inside.

  Direct sunlight may cause an abnormal rise in the temperature inside the instrument and 

discoloration or deterioration of resin parts. Also, removing the cover for maintenance during 

rain may damage the electrical parts inside the instrument.

  Install the instrument in a building or cabinet away from direct sunlight and rainwater.

•  With little vibration

  Vibration may result in incomplete connections such as external wiring.

•  Where corrosive gases are not present.

  Corrosive gas can damage electrical component inside the instrument.

•  Where humidity of 0 to 90% RH is maintained (No condensation)

  No installing in a place with high humidity.

•  With little temperature change, close to normal temperature

  The ambient temperature must not exceed the range of -5 to 55°C.

  If the temperature of the sample is lower than the ambient temperature, it may cause 

condensation.

  Take protective measures to prevent a sample and the tap water from freezing, if necessary.

•  With adequate maintenance space and easy access for maintenance work.

  Secure sufficient maintenance space for maintenance such as replacement, cleaning, and 

calibration.

•  Where the drain is provided

  The sample needs to be drained during cleaning and calibration, so install it in a place 

where drainage is possible.

•  Near the place where the converter is installed (without sampling system)

  Consider the length of the connection cable to the converter when installing.

Содержание TB830D






















































































Отзывы:

Нет отзывов