YOKOGAWA TB830D Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 85

YOKOGAWA TB830D Скачать руководство пользователя страница 52

< 7. Calibration >

7-1

IM 12E01B30-02EN

1st Edition : Mar. 08, 2023-00

7. CALIBRATION

This chapter describes types of calibration enabled with TB830D. Periodical calibration and

an optimization of calibration parameters for Zero or Slope ensure accurate measurement.

The sensitivity correction can also correct the standard and grab sample sensitivity. Clean the

Flow cell before calibration. Perform calibration with the detectors or the Flow cells free from

contamination when the reading is stable.

7.1

Turbidity calculation and calibration menu

Zero, Slope are adjusted based on a standard solution as a reference. (Equation 7.1)

If the turbidity measured by the instrument may differ from the one measured manually in a lab

due to the difference of properties of the sample and/or of turbidity measurement methods, the

instrument can be adjusted so that it reads the same value as the one measured in a lab by

performing the zero shift correction or sensitivity correction.
In this case, the instrument determines zero and sensitivity correction factors in addition to the

calibration factor determined based on the calibration using standards. (See Equation 7.2.)
Normally T2 represents a turbidity, but when Zero calibration, Slope calibration (check tool,

standard solution), Auto Zero Calibration, Sensitivity correction calibration is being progressed,

T1 is used.

T1 = [100/SL/S

0

]*[V-A]

......

Equation 7.1

T2 = K*T1 + B

.....................

Equation 7.2

Where:

T1: Turbidity based on turbidity standards

S0: Sensitivity factor

Calculated reference sensitivity calibration. This calibration is performed at the factory

before shipment.

SL: Slope

Calibrated by slope calibration. SL(%) value means how different sensitivity is from

factory sensitivity.

A: Zero

Calculated in zero calibration using zero water.

V: Measuring signal

This signal is calculated by ratio of scattered light current and light source monitoring

current.

T2: Turbidity after zero and sensitivity corrections

K: Correction factor

Determined in sensitivity corrections or 2-point sensitivity corrections.

B: Zero shift value

Determined in zero shift corrections or 2-point sensitivity corrections.

«
...
50
51
52
53
54
...
»

Содержание TB830D






















































































Отзывы:

Нет отзывов