manualshive.com logo in svg

YOKOGAWA TB830D, Руководство пользователя, Страница: 42 / 85

Поделиться
Скачать
YOKOGAWA TB830D Скачать руководство пользователя страница 42

  

< 4. SETTING PARAMETERS >

4-7

IM 12E04B40-02EN

1st Edition : Mar. 08, 2023-00

4.3.3 

Operating days

Set each counts of parameter enabled/disabled

If you want to confirm the value of operation days, enable the function. However, even if you set it 

disabled, the operating day counts internally. TB830D does not use the Wiper operating days.

4.4 

Communication setting

n

  Sensor connection address

You can change Modbus address. Normally, you do not need to change setup. After changing 

Modbus address, you need to change the configuration of the converter that connects to the 

system. To change the converter setting, Converter menu > Setting > Converter setting > 

Advanced settings > MODBUS setting >Sensor Address setting (S) Refer FLXA402T Operation 

of Converter (IM 12A01G01-03EN).

CAUTION

The change in sensor addressing setup is reflected by turning OFF/ON Power Supply.

4.5 

Automatic cleaning/Automatic zero 

calibration setting

This setup is a converter setup.

4.5.1 

Auto sequence for wash/cal.

Enable this function to use Automatic cleaning/Automatic zero calibration.
If this function is disabled, automatic cleaning/automatic zero calibration is never implemented 

even if other setting is active.

4.5.2 

Start date

First set the date and time to activate automatic cleaning/automatic zero calibration. As the first 

time automatic cleaning/automatic zero calibration, enter a future date/time but not the current 

one.
If you want to perform the next and subsequent automatic cleaning/automatic zero calibration 

automatically, turn ON Auto update of start date. The next date of automatic cleaning/automatic 

zero calibration is determined according to the washing interval.

4.5.3 

Automatic cleaning/Automatic zero calibration 

function and wash type

You can set Automatic cleaning function and Automatic zero calibration function respectively to 

Enable/Disable. When you use Auto calibration, always set Automatic cleaning to Enable Always 

select water flow as wash type.

Содержание TB830D






















































































Отзывы:

Нет отзывов