background image

Check & secure work clamp.

Poor work clamp connection.

No gas, incorrect gas flow.

Check the gas is connected and cylinder valve open, check 
hoses,  gas  valve  and  torch  are  not  restricted.  Set  the  gas 
flow between 20-30 CFH flow rate.

PROBLEM

POSSIBLE CAUSE

COURSE OF ACTION

Lift TIG does not ini-
tiate an arc.

TROUBLESHOOTING

TIG WELDING ISSUES

Check all connectors and tighten.

Loose connection.

Connect  the  work  clamp  directly  to  the  work  piece  wher-
ever possible.

Earth clamp not connected to work.

Grind to ctean Tungsten.

Contaninated Tungsten.

Tungsten  burning 
away quickly.

Incorrect Gas/Inadequate gas flow.

Check  the  gas  cylinder  contains  pure  Argon  gas  and  is 
connected  and  the  torch  gas  valve  is  open.  Set  the  gas 
flow between 20-30 CFH flow rate.

Make sure the torch back cap is fitted so that the o-ring is 
inside the torch body.

Back cap not fitted correctly.

Check and change the tungsten type if necessary.

Incorrect tungsten being used.

Contaminated  tung-
sten.

Touching the filler wire to the tungsten.

Keep  the  filler  wire  from  touching  the  tungsten  during 
welding,  feed  the  filler  wire  into  the  leading  edge  of  the 
weld pool in front of the tungsten.

Keep  tungsten  from  contacting  weld  puddle.  Raise  the 
torch so that the tungsten is off of the work piece 1/8-1/4.

Touching tungsten into the weld pool.

Check  that  correct  type  of  tungsten  is  being  used.  Too 
much  current  for  the  tungsten  size  so  reduce  the  amps  or 
change to a larger tungsten.

Tungsten melting into the weld pool.

- 31 -

Содержание YWM-211P









































Отзывы: