10
O R I G I N A L I N S T R U C T I O N S
GB
prevent burns. Make sure, that the
fl
oor near the cooker is not slippery. This will allow you to
prevent slips, which can cause severe injuries.
PRODUCT SERVICE
Installation, starting and operation of the product
You should unpack the product, completely remove all the elements of the packaging; it is recommended that you keep the pack-
aging, it may be useful for later transport and storage of the product.
Wash the product in accordance with the instructions from the point “Product maintenance”.
Put on the product an appropriate,
fi
lled vessel.
The heating plate is equipped with a sensor that allows you to run the product in the absence of the dish on a plate or when the
vessel bottom has a smaller diameter than these, which is speci
fi
ed in the technical data table.
Make sure, that the knob is in the “o
ff
” position. and then insert the plug of product to the mains wall socket.
By using the knob you should set the power range within the range, which is speci
fi
ed in the table.
After work completion you should turn o
ff
the cooker by setting the knob to its position “ON/OFF”, and then remove the vessel
from cooker.
WARNING!
When you remove the vessel from cooker you should be very careful. The vessel and cooker plate can are very hot
and can cause serious burns. Use personal protective equipment in the form of gloves and protective clothing.
You should allow the cooker plate to cool down spontaneously, and then proceed to maintenance as described in section “ Product
maintenance”
ATTENTION!
The cooker will turn o
ff
automatically after two hours since the last time of power change with its knob.
Maintenance of the product
ATTENTION!
All maintenance operations must be carried out when the product power supply is turned o
ff
.
To do this you should
remove the power cord plug from a mains outlet.
Heating plate and other parts of the product should be cleaned by using a cloth soaked in water solution of mild dishwasher liquid.
After the cleaning, you should wipe dry the product. The plate should be cleaned after each use, after it completely cools down.
You should clear all food remains, which have been left on the plate, this will prevent their overcooking during subsequent use,
this will also prevent the performance degradation of product.
For cleaning do not use solvents, aggressive agents, the alcohol gasoline, or abrasive cleaners.
Vents should be cleaned by using a vacuum cleaner.
Attention! Never immerse the product in water or any other liquid.
Storage of the product
If the product will not be used for an extended period of time, you should disconnect it from power supply.
Store the product indoors, protect against dust, dirt and moisture. It is recommended to store the product in the factory packaging.
Store the product in its working position. Do not install the products in layers. Do not place anything on the product during its
storage.
TECHNICAL DATA
Parameter
Unit
Value
Catalog number
YG-04700
Rated voltage
[V~]
220 - 240
Rated frequency
[Hz]
50 - 60
Rated power
[W]
3500
Adjustable range of power
[W]
500 - 3500
Insulation class
I
Operating Frequency
[kHz]
18 – 30
Degree of protection
IP23
Noise level - acoustic pressure
[dB(A)]
<70
Minimum diameter of the vessel bottom
[cm]
12
Maximum diameter of the vessel bottom
[cm]
26
Maximum weight of the vessel
[kg]
15
Operating temperature range
[
O
C]
+60 ÷ +240
Net weight
[kg]
5.6
Содержание YG-04700
