YASKAWA VS-616PS5 Series Скачать руководство пользователя страница 68

Страница: 68 / 109

VS-616PS5 Installation & Quick Start Manual

DEV

Speed Deviation

Speed deviation

(DEV)

The deviation of the speed reference and

speed feedback exceeded the regulation

level. (F1-10)

Check the load.

STO

Step Out

Stepout

Motor has pulled out of synchronization with

the applied stator field.

• Check the motor constants.

• Check the motor tempera-

ture.

• Reduce the ASL gain (C5-

01).

• Reduce the acceleration (C1-

01).

Zdev

Phase Z Pulse

Fault

Phase Z pulse fault

(Marker Pulse)

An uncontrolled motor state results from an

incomplete PG origin pulse adjustment or

from a failed initial magnetic pole estimation.

• Check the PG cable connec-

tion.

• Repeat auto-tuning (set T1-

03 = 1, then T1-02 = 2, and

press the digital operator

RUN key).

External Fault

Simultaneous forward/

reverse run com-

mands

Both FWD and REV run commands are simul-

taneously input for 500ms or longer.

Check sequence circuit.

Base Block

External base block

External base block command is input from

control circuit terminal.

Check sequence circuit.

EF3

External Fault 3

External fault at

terminal 3

Fault occurred in the external control circuit.

Check the condition of the input

terminal. If the LED lights when

the input is not activated, then

the inverter requires repair.

EF4

External Fault 4

External fault at

terminal 4

Fault occurred in the external control circuit.

Check the condition of the input

terminal. If the LED lights when

terminal is not connected, then

the inverter requires repair.

EF5

External Fault 5

External fault at

terminal 5

EF6

External Fault 6

External fault at

terminal 6

EF7

External Fault 7

External fault at

terminal 7

EF8

External Fault 8

External fault at

terminal 8

OPE01

kVA Selection

kVA setting error

(OPE01)

Inverter kVA setting error.

Check and set the parameter

data

(O2-04)

OPE02

Limit

Parameter setting

range error (OPE02)

Parameter data is out of range.

Check the parameter data set-

tings.

OPE03

Terminal

Multi-function input

setting error (OPE03)

Multi-function input settings in

H1-01

H1-06

are not in ascending order. Or, set values

other than “F” are overlapping

Check the function selection.

OPE05

Option reference

selection fault

(OPE05)

• C-option is not connected although run

command from C-option is selected

• C-option is not connected although fre-

quency reference from C-option is selected

• Check and set the contstant

data.

• Connect the C-option.

OPE06

Control method selec-

tion fault (OPE06)

PG control card is not connected during flux

vector control.

Connect PG control card.

Fault Display

Name

Description

Corrective Action

Class

Содержание VS-616PS5 Series














































































































Результаты поиска

Содержание VS-616PS5 Series

Отзывы:

YASKAWA VS-616PS5 Series, Быстрый старт, Страница: 68 / 109

Результаты поиска

Содержание VS-616PS5 Series

Отзывы: