manualshive.com logo in svg

YASKAWA MOTOMAN-ES200RN, Инструкция по эксплуатации, Страница: 60 / 82

Поделиться
Скачать
YASKAWA MOTOMAN-ES200RN Скачать руководство пользователя страница 60

9.2  Notes on Maintenance Procedures

9-13

HW0482143

Grease Exchange (Refer to " Fig. 26 U-Axis Speed Reducer Dia-
gram ".)

1.

Tilt the U-arm horizontal to ground.

2.

Remove the hexagon socket head plug PT1/8 from the grease exhaust port.

3.

Remove the hexagon socket head plug PT1/8 from the grease inlet and install the 
grease zerk A-PT1/8.  Inject grease into the grease inlet using a grease gun.  (The 
grease zerk is delivered with the manipulator.)

4.

The grease exchange is completed when new grease appears in the grease exhaust 
port.  The new grease can be distinguished from the old grease by color.

5.

Move the U-axis for a few minutes to discharge excess grease.

6.

Wipe the grease exhaust port with a cloth and reinstall the plug PT1/8.  Tighten the 

plug with a tightening torque of 4.9 N m (0.5 kgf m).  (Apply Three Bond 1206C to the 

thread part of the plug.)

7.

Remove the grease zerk from the grease inlet and reinstall the plug PT1/8.  Tighten the 

plug with a tightening torque of 4.9 N m (0.5 kgf m).  (Apply Three Bond 1206C to the 

thread part of the plug.)

If grease is added with the plug on, the grease will go inside the motor and may damage it. 
It is absolutely necessary to remove the plug.

Grease type: Molywhite RE No.00

Amount of grease: approx. 1800cc

If the plug is installed when the grease is being exhausted, the grease will go inside the 
motor and may damage it.

NOTE

NOTE

59/71

HW0482143

Содержание MOTOMAN-ES200RN



















































































Отзывы:

Нет отзывов