YASKAWA MOTOMAN-ES200RN Скачать руководство пользователя страница 67

Страница: 67 / 82

9.2 Notes on Maintenance Procedures

9-20

HW0482143

9.2.5

Grease Replenishment for Balancer Connection Part

Fig. 28 Balancer Connection Part

Remove the hexagon socket head cap screw M6 and hexagon socket head plug PT1/8
from the grease inlets and exhaust ports of connection and . (Refer to " Fig. 28
Balancer Connection Part ".)

Install the grease zerk A-PT1/8 on the grease inlets of connection and and inject

grease into the grease inlets using a grease gun.

Grease type: Alvania EP grease 2

Amount of grease: 5cc

(10cc for 1st supply)

The exhaust ports and are used for air flow.
Do not inject excessive grease into the grease inlets.

Exhaust port
Hexagon socket head plug PT1/8

Connection
Grease inlet
Hexagon socket head plug PT1/

Connection
Needle bearing (2 bearings)

Connection
Grease inlet
Hexagon socket head plug PT1/8 (2 plugs)

Exhaust port
Hexagon socket head cap screw M6 (2 screws)

Connection
Tapered roller bearing (2 bearings)

NOTE

66/71

HW0482143

Содержание MOTOMAN-ES200RN



















































































Результаты поиска

Содержание MOTOMAN-ES200RN

Отзывы:

YASKAWA MOTOMAN-ES200RN, Инструкция по эксплуатации, Страница: 67 / 82

Результаты поиска

Содержание MOTOMAN-ES200RN

Отзывы: