manualshive.com logo in svg

YASKAWA MOTOMAN-ES200RN, Инструкция по эксплуатации, Страница: 63 / 82

Поделиться
Скачать
YASKAWA MOTOMAN-ES200RN Скачать руководство пользователя страница 63

9.2  Notes on Maintenance Procedures

9-16

HW0482143

Grease Replenishment for B-Axis Speed Reducer (Refer to " Fig. 27 
U-Arm Diagram ".)

1.

Remove the hexagon socket head plug PT1/8 from the grease exhaust port.

2.

Remove the hexagon socket head plug PT1/8 from the grease inlet and install the 
grease zerk A-PT1/8.  Inject grease into the grease inlet using a grease gun.  (The 
grease zerk is delivered with the manipulator.)

3.

Move the B-axis for a few minutes to discharge excess grease.

4.

Wipe the grease exhaust port with a cloth and reinstall the plug PT1/8.  Tighten the 

plug with a tightening torque of 4.9 N m (0.5 kgf m).  (Apply Three Bond 1206C to the 

thread part of the plug.)

5.

Remove the grease zerk from the grease inlet and reinstall the plug PT1/8.  Tighten the 

plug with a tightening torque of 4.9 N m (0.5 kgf m).  (Apply Three Bond 1206C to the 

thread part of the plug.)

Grease Replenishment for T-Axis Speed Reducer (Refer to " Fig. 27 
U-Arm Diagram ".)

1.

Remove the hexagon socket head plug PT1/16 from the grease exhaust port.

2.

Remove the hexagon socket head plug PT1/8 from the grease inlet and install the 
grease zerk A-PT1/8.  Inject grease into the grease inlet using a grease gun.  (The 
grease zerk is delivered with the manipulator.)

3.

Move the T-axis for a few minutes to discharge excess grease.

4.

Wipe the grease exhaust port with a cloth and reinstall the plug PT1/16.  Tighten the 

plug with a tightening torque of 4.9 N m (0.5 kgf m).  (Apply Three Bond 1206C to the 

thread part of the plug.)

5.

Remove the grease zerk from the grease inlet and reinstall the plug PT1/8.  Tighten the 

plug with a tightening torque of 4.9 N m (0.5 kgf m).  (Apply Three Bond 1206C to the 

thread part of the plug.)

If grease is added with the plug on, the grease will go outside the grease box and may 
damage it. It is absolutely necessary to remove the plug.

Grease type: Molywhite RE No.00

Amount of grease: 260cc

(520cc for 1st supply)

If grease is added with the plug on, the grease will go outside the grease box and may 
damage it. It is absolutely necessary to remove the plug.

Grease type: Molywhite RE No.00

Amount of grease: 260cc

(520cc for 1st supply)

NOTE

NOTE

62/71

HW0482143

Содержание MOTOMAN-ES200RN



















































































Отзывы:

Нет отзывов