manualshive.com logo in svg

YASKAWA MOTOMAN-ES200RN, Инструкция по эксплуатации, Страница: 59 / 82

Поделиться
Скачать
YASKAWA MOTOMAN-ES200RN Скачать руководство пользователя страница 59

9.2  Notes on Maintenance Procedures

9-12

HW0482143

9.2.4

Grease Replenishment/Exchange for U-Axis Speed 
Reducer

Fig. 26   U-Axis Speed Reducer Diagram

Grease Replenishment (Refer to " Fig. 26 U-Axis Speed Reducer 
Diagram ".)

1.

Tilt the U-arm horizontal to ground.

2.

Remove the hexagon socket head plug PT1/8 from the grease exhaust port.

3.

Remove the hexagon socket head plug PT1/8 from the grease inlet and install the 
grease zerk A-PT1/8.  Inject grease into the grease inlet using a grease gun.  (The 

grease zerk is delivered with the manipulator.)

4.

Move the U-axis for a few minutes to discharge excess grease.

5.

Wipe the grease exhaust port with a cloth and reinstall the plug PT1/8.  Tighten the 

plug with a tightening torque of 4.9 N m (0.5 kgf m).  (Apply Three Bond 1206C to the 

thread part of the plug.)

6.

Remove the grease zerk from the grease inlet and reinstall the plug PT1/8.  Tighten the 

plug with a tightening torque of 4.9 N m (0.5 kgf m).  (Apply Three Bond 1206C to the 

thread part of the plug.)

If grease is added with the plug on, the grease will go inside the motor and may damage it. 
It is absolutely necessary to remove the plug.

Grease type: Molywhite RE No.00

Amount of grease: 280cc

(560cc for 1st supply)

Grease exhaust port
Hexagon socket head plug PT1/8

Grease inlet
Hexagon socket head plug PT1/8

NOTE

58/71

HW0482143

Содержание MOTOMAN-ES200RN



















































































Отзывы:

Нет отзывов