YardCraft Phobos Vinyl Playset Скачать руководство пользователя

Страница: 2 / 23

Tools Required for Job

One 4' Step

Ladder

Cordless Drill

& 1/2" drill bit

& 5/16" drill bit

25’ Tape

Measure

Phobos

Vinyl Playset

Assembly Manual

Thank you for your purchase of this playset.

This manual is designed to simplify the assembly process, however we recommend having an experienced

carpenter involved in the project. Please read through the entire manual before starting!

Take a deep breath and get at it; the satisfaction and enjoyment of this hideout is only a few minutes away.

Have fun!

You have purchased a product that consists of bulky pieces. With your purchase, you assume full

responsibility to have the necessary manpower available to assemble the product. You also agree that any

damage that happens to the product during the entire construction process is your responsibility, and neither

the seller, nor the manufacturer, will be held liable for any such damage.

9/16th Wrench

#2 Square

Drive Tip

(included)

T30 Star

Drive Tip

(included)

9/16" deep socket

Содержание Phobos Vinyl Playset
























Результаты поиска

Содержание Phobos Vinyl Playset

Отзывы:

Похожие инструкции для Phobos Vinyl Playset

Бренды по названию

Популярные бренды

YardCraft Phobos Vinyl Playset, Инструкция по сборке

Результаты поиска

Содержание Phobos Vinyl Playset

Отзывы:

Похожие инструкции для Phobos Vinyl Playset

Бренды по названию

Популярные бренды