background image

6

7

GB

GB

Ponds and Pools

While the Robotic Mower is protected against rain and spray water, being submerged is likely to 
cause severe damage to the electronic parts.
Therefore, it is imperative to exclude any pools from the cutting area. For added safety, we 
recommend placing a fence around the pool.

Inventory and garage

If you have created a boundary corridor inside your working area, the corridor should be at least 2 
m wide and a max length of 8 m.
If a corridor is too narrow or too long, the Robotic Mower might not be able to navigate it from one 
end to the other.

 

 

Connect the docking station to the boundary wire

Run the boundary wire underneath the front of the docking station and connect the end of the
wire to the left (black) connector marked 'F' (front). After you have placed the wire around the
garden then place the other end into right (red) connector marked "B" (back).

10-15 mm

    

< 8 m

> 2 m

correct distance from lawn edges (30 cm) and obstacles.

Flowerbeds

Use the boundary wire to exclude any flowerbeds from the cutting area. There are two options for 
the two lengths of boundary wire running between the flowerbed and the outer boundary:
1) Keep the distance between the parallel wires above 5 cm. This way, the Robotic Mower will 
recognise the boundary wire as an ordinary obstacle. When cutting, it will "bounce" off it as usual. 
When following the boundary wire back to the docking station, it will take the detour around the 
flower bed.

> 5 cm

     

2) Alternatively, keep the distance between the two parallel wires below 5 cm. Do not cross the 
wires - 

see below

. This way, the Robotic Mower will not recognise the wires and travel across 

them unhindered. This option requires placing an obstacle on the boundary wire around the 
flowerbed. Place the obstacle, e. g. a large rock or pole, near 

position A

 indicated on the below 

illustration. The obstacle must be surrounded by a flat area of about 1 m x 1 m, without any 
slopes. This obstacle will allow the machine to exit the circle.

< 5 cm

 

5 cm

<

5 cm

A

> 5 cm

Содержание Classic 500













Отзывы: