background image

12

GB

Changing the PIN Code

1. Switch Off the mains power switch.
2. Hold down the lock button          while switch ON the main power switch. After few 
seconds, all indicators on the control panel will start flashing.
3. Release the lock button          .
4. Enter you new PIN-Code within 6 seconds, the Robotic Mower will confirm and changed 
PIN with a beep.

5. All indicators will turn off and the Robotic Mower will reboot, and the indicator of lock 
button will flash, confirming that the reboot is complete. 

NOTE:

 if you do not remember your PIN code, please set a new PIN code as described 

above, but it is not possible to reset the device to the default PIN-code of 4X            .

Cutting height adjustment

The cutting height can be adjusted by rotating the height adjustment dial located on the top 
of the machine. Cutting height range from 20 mm - 60 mm.

NOTE! 
We recommend using an ordinary lawn mower or trimmer to cut the lawn below 60 mm 
before using the Robotic Mower. This will ensure you get the optimum performance.

for example:
if now is 08:25, please press            , and then you would hear a beep.
if now is 09:45, please press            , and then you would hear a beep.
if now is 14:25, please press            , and then you would hear a beep.
if now is 16:45, please press            , and then you would hear a beep.

Three seconds later, all these LED will flash off                                                                

Congratulations, all calibration have been completed, The mower will restart, now you can enjoy 
the scheduled mowing in your garden.

Start mowing

After finishing the time settings, now you can start your Robotic Mower
1. Press the          button for 4 times to unlock the panel.
2. Press the button              and then press the button           , the Robotic Mower will start to work. 

Return to the docking station

1. Press the          button for 4 times to unlock the panel.
2. Press the button           and then press the button           , the Robotic Mower will back to the 
docking station. 

Emergency Stop

Press STOP button to halt the mower at any time.

Содержание Classic 500













Отзывы: