background image

8

9

GB

GB

Signal selection

Note:

 the default signal is S1, no need to change the signal when there isn’t a influence signal 

form the neighbors.

S1

S2

S1

S2

If your neighbour is using the same mower, you will need to keep a distance of 0.5m between 
you and your neighbour's boundary wires to prevent the two devices interfering with each other. 
Ensure to position your docking station at least 10m away from your neighbour's boundary wires 
and that both products are using different signals. Please refer to section "Signal setting" in order 
to select signal S1 or S2 for your installation.
1.  Press the “signal” button on the charging station, the indicator will be switched to S2.
2.  Press the "S2" button on the control panel. the indicator will be switched to S2

>10 m

>10 m

>0.5 m

S1

S2

Insert the mains plug into a properly installed socket. Once the blue LED confirms all is OK, test 
the Robotic Mower's function. Check the LED regularly to ensure fixing the boundary wire has not 
affected the connection and signal shows S1 on the charging satation. Then place the Robotic 
Mower in the working area, a few metres beside the docking station. Set the main power switch 
to "ON". and then check  the S1 signal on the panel is light on, press          4 times to unlock the 
panel.

Press the buttons 

 and 

 , a few seconds later, the Robotic Mower should automatically 

return to the docking station by locating and following the boundary wire in anti-clockwise 
direction. If Robotic Mower fails to dock correctly, move the docking station to a more suitable 
position.

Once the device has docked, the symbol              on the panel will start flashing, and the S1&S2 
indicators on the docking station will flash alternately

This indicates that the battery is charging 

correctly.

After initial installation, the Robotic Mower will remain in the docking station until the battery is 
fully charged.

Successful docking and charging indicates that you have found a suitable position for the docking 
station. You should now drive fixing pegs into ground fully.
Take care not to damage or kink the surplus wire stored under the docking station.

1

2

S1

S2

Содержание Classic 500













Отзывы: