Yamaha YFM70RSBG Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 160

Yamaha YFM70RSBG Скачать руководство пользователя страница 46

4-18

4

Compression damping force

Compression damping force (for fast compres-
sion damping)
To increase the compression damping force and
thereby harden the compression damping, turn
the compression damping force adjusting bolt in
direction (a). To decrease the compression damp-
ing force and thereby soften the compression
damping, turn the adjusting bolt in direction (b).

Rebound damping setting:

Minimum (soft):

30 click(s) in direction (b)*

Standard:

18 click(s) in direction (b)*

Maximum (hard):

1 click(s) in direction (b)*

* With the adjusting screw fully turned in di-

rection (a)

1. Compression damping force adjusting bolt (for fast

compression damping)

Compression damping setting (for fast com-
pression damping):

Minimum (soft):

2 turn(s) out from the fully turned in posi-
tion

Standard:

1.5 turn(s) out from the fully turned in po-
sition

Maximum (hard):

Adjusting bolt fully turned in

1

(a)

(b)

1

U2LS61E0.book Page 18 Friday, April 17, 2015 8:25 AM

«
...
44
45
46
47
48
...
»

Содержание YFM70RSBG

































































































































































Отзывы:

Нет отзывов