manualshive.com logo in svg

Yamaha YFM70RSBG, Руководство пользователя

Поделиться
Скачать
Yamaha YFM70RSBG Скачать руководство пользователя страница 106

8-14

8

Be sure the engine oil is at the correct lev-
el, otherwise engine damage may result.

[ECB00852]

TIP

When adding oil, be careful not to overfill the en-
gine oil tank; the oil level rises faster starting from
the half-level-portion on the dipstick.

 

6. Insert the dipstick into the engine oil tank filler

hole, and then tighten the engine oil tank filler
cap. 

NOTICE:

 Make sure that the engine oil

tank filler cap is securely tightened; other-
wise, oil may seep out when the engine is
running.

 [ECB00363]

To change the engine oil (with or without oil fil-
ter element replacement)

1. Place the ATV on a level surface.
2. Start the engine, warm it up for several min-

utes, and then turn it off.

3. Place an oil pan under the engine to collect

the used oil.

4. Remove the crankcase engine oil filler bolt

and its O-ring, and then remove the crank-
case engine oil drain bolt and its gasket.

1. Crankcase engine oil filler bolt
2. O-ring

1. Crankcase engine oil drain bolt
2. Gasket

2

1

1

2

U2LS61E0.book  Page 14  Friday, April 17, 2015  8:25 AM

Содержание YFM70RSBG

































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды