Yamaha YFM70RSBG страница 110 Скачать руководство пользователя | Manualshive

Страница: 110 / 160

background image

8-18

8

TIP

The coolant level must be checked on a cold en-
gine since the level varies with engine tempera-
ture.

2. Check the coolant level in the coolant reser-

voir.

TIP

The coolant should be between the minimum and
maximum level marks.

3. If the coolant is at or below the minimum level

mark, remove the coolant reservoir cap, add
coolant or distilled water to the maximum lev-
el mark, and then install the reservoir cap.

NOTICE:

If coolant is not available, use

distilled water or soft tap water instead.
Do not use hard water or salt water since
they are harmful to the engine. If water has
been used instead of coolant, replace it
with coolant as soon as possible, other-
wise the cooling system will not be pro-
tected against frost and corrosion. If water
has been added to the coolant, have a
Yamaha dealer check the antifreeze con-
tent of the coolant as soon as possible,
otherwise the effectiveness of the coolant
will be reduced.

[ECB01012]

1. Maximum level mark
2. Minimum level mark

1

2

U2LS61E0.book Page 18 Friday, April 17, 2015 8:25 AM

«
...
108
109
110
111
112
...
»

Содержание YFM70RSBG

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YFM70RSBG

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды