Yamaha YFM70RSBG страница 130 Скачать руководство пользователя

Страница: 130 / 160

8-38

8. Tighten the locknut at the clutch lever, and

then slide the rubber cover to its original po-
sition.

TIP

If the specified free play cannot be obtained as de-
scribed above or if the clutch does not operate
correctly, have a Yamaha dealer check the internal
clutch mechanism.

EBU26865

Drive chain slack

The drive chain slack should be checked before
each ride and adjusted if necessary.

To check the drive chain slack

1. Place the ATV on a level surface.

TIP

When checking and adjusting the drive chain
slack, there should be no weight on the ATV and
all tires must be touching the ground.

2. Move the ATV back and forth to locate the

tightest portion of the drive chain, and then
measure the drive chain slack as shown.

3. If the drive chain slack is incorrect, adjust it as

follows.

To adjust the drive chain slack

1. Place the ATV on a level surface.
2. Loosen the rear wheel axle pinch bolts.
3. Insert a rod of a diameter of 8 mm (0.3 in) and

a length of 10 cm (4 in) into one of the holes in
the drive chain tensioner as shown.

Drive chain slack:

25.0–35.0 mm (0.98–1.38 in)

1. Drive chain slack

U2LS61E0.book Page 38 Friday, April 17, 2015 8:25 AM

Содержание YFM70RSBG

































































































































































Результаты поиска

Содержание YFM70RSBG

Отзывы:

Похожие инструкции для YFM70RSBG

Бренды по названию

Популярные бренды

Yamaha YFM70RSBG, Руководство пользователя

Результаты поиска

Содержание YFM70RSBG

Отзывы:

Похожие инструкции для YFM70RSBG

Бренды по названию

Популярные бренды