Yamaha YFM70RSBG страница 50 Скачать руководство пользователя | Manualshive

Страница: 50 / 160

background image

4-22

4

EBU30991

Adjusting the rear shock absorber as-
sembly (YFM70RSSG)

This shock absorber assembly is equipped with a
spring preload adjusting nut, a rebound damping
force adjusting screw, with a compression damp-
ing force adjusting bolt (for fast compression
damping), and a compression damping force ad-
justing screw (for slow compression damping).

WARNING

EWB02681

Suspension components become hot during
operation. Never touch the compression
damping force adjusting bolt and screw, the
rebound damping force adjusting screw or the
oil reservoir with your bare hand or skin until
the suspension components have cooled.

NOTICE

ECB00091

Never turn an adjusting mechanism beyond
the minimum and maximum settings.

TIP

Although the total number of clicks or turns of a
damping force adjusting mechanism may not ex-
actly match the following specifications due to
small differences in production, the actual number
of clicks or turns always represents the entire ad-
justing range. To obtain a precise adjustment, it
would be advisable to check the number of clicks
or turns of each damping force adjusting mecha-
nism and to modify the specifications as neces-
sary.

Spring preload

1. Loosen the locknut.
2. Turn the spring preload adjusting nut in direc-

tion (a) to increase the spring preload and
thereby harden the suspension, and in direc-
tion (b) to decrease the spring preload and
thereby soften the suspension.

U2LS61E0.book Page 22 Friday, April 17, 2015 8:25 AM

«
...
48
49
50
51
52
...
»

Содержание YFM70RSBG

































































































































































Отзывы:

Нет отзывов

Похожие инструкции для YFM70RSBG

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды