Yamaha YFM70RSBG страница 127 Скачать руководство пользователя

Страница: 127 / 160

8-35

1. Release the parking brake by moving the

parking brake lever to the right.

2. Fully loosen the locknut and the adjusting bolt

at the rear brake caliper.

3. Slide the rubber cover back at the brake ca-

ble.

4. Loosen the locknut.
5. Turn the parking brake free play adjusting nut

in direction (a) to increase the cable length,
and in direction (b) to decrease it.

TIP

If the cable length cannot be adjusted to specifi-
cation, consult a Yamaha dealer.

6. Tighten the locknut on the brake cable.
7. Slide the rubber cover to its original position.
8. Turn in the adjusting bolt at the rear brake cal-

iper until it feels tight, then turn it out 1/8 turn
and tighten its locknut to the specified torque.

NOTICE:

When tightening the locknut,

1. Adjusting bolt
2. Cable length “A”
3. Locknut

1. Rubber cover
2. Parking brake free play adjusting nut
3. Locknut

(b)

(a)

U2LS61E0.book Page 35 Friday, April 17, 2015 8:25 AM

Содержание YFM70RSBG

































































































































































Результаты поиска

Содержание YFM70RSBG

Отзывы:

Похожие инструкции для YFM70RSBG

Бренды по названию

Популярные бренды

Yamaha YFM70RSBG, Руководство пользователя

Результаты поиска

Содержание YFM70RSBG

Отзывы:

Похожие инструкции для YFM70RSBG

Бренды по названию

Популярные бренды