Yamaha YFM35RX Скачать руководство пользователя | Manualshive

Страница: 92 / 134

background image

8-14

8

NOTE:

Be sure to wipe off spilled oil on any parts after the
engine and exhaust system have cooled down.

CAUTION:

ECB00300

●

In order to prevent clutch slippage (since the
engine oil also lubricates the clutch), do not
mix any chemical additives. Do not use oils
with a diesel specification of “CD” or oils of
a higher quality than specified. In addition,
do not use oils labeled “ENERGY CONSERV-
ING II” or higher.

●

Make sure that no foreign material enters the
crankcase.

12. Start the engine, and then let it idle for several

minutes while checking it for oil leakage. If oil
is leaking, immediately turn the engine off and
check for the cause.

13. Turn the engine off, wait at least ten minutes,

and then check the oil level and correct it if
necessary.

EBU23741

Cleaning the air filter element

The air filter element should be cleaned at the in-
tervals specified in the periodic maintenance and
lubrication chart. Clean the air filter element more
frequently if you are riding in unusually wet or dusty
areas.

NOTE:

There is a check hose at the bottom of the air filter
case. If dust or water collects in this hose, empty
the hose and clean the air filter element and air fil-
ter case.

Recommended oil:

See page 10-1.

Oil quantity:

Without oil filter element replacement:

2.50 L (2.64 US qt) (2.20 Imp.qt)

With oil filter element replacement:

2.60 L (2.75 US qt) (2.29 Imp.qt)

U5YT64E0.book Page 14 Monday, April 9, 2007 1:03 PM

«
...
90
91
92
93
94
...
»

Содержание YFM35RX







































































































































Отзывы:

Нет отзывов

Похожие инструкции для YFM35RX

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды