Yamaha YFM35RX Скачать руководство пользователя страница 106 | Manualshive

Страница: 106 / 134

Yamaha YFM35RX Скачать руководство пользователя страница 106

8-28

8

EBU24820

Adjusting the clutch lever free play

The clutch lever free play must be checked and, if
necessary, adjusted at the intervals specified in the
periodic maintenance and lubrication chart.
The clutch lever free play should measure 5.0–
10.0 mm (0.20–0.39 in) as shown. If the free play
is incorrect, adjust it as follows.

1. Loosen the locknut at the clutch lever.
2. To increase the clutch lever free play, turn the

adjusting bolt at the clutch lever in direction
(a), and to decrease it, turn the bolt in direction
(b).

3. Tighten the locknut at the clutch lever.

If the specified free play cannot be obtained,
proceed with the following steps.

4. Loosen the locknut at the clutch lever.
5. Fully turn the adjusting bolt at the clutch lever

in direction (a) to loosen the clutch cable.

6. Loosen the locknut at the crankcase.

1. Brake light switch
2. Brake light switch adjusting nut

1. Locknut
2. Clutch lever free play adjusting bolt

3. Clutch lever free play

U5YT64E0.book Page 28 Monday, April 9, 2007 1:03 PM

«
...
104
105
106
107
108
...
»

Содержание YFM35RX







































































































































Отзывы:

Нет отзывов