Yamaha YFM35RX Скачать руководство пользователя

Страница: 91 / 134

8-13

5. Remove the oil filter element cover by remov-

ing the bolts, and then remove the oil filter el-
ement.

6. Clean the oil strainer and oil filter element with

solvent.

7. Check the O-rings for damage and replace it if

necessary.

8. Install the oil filter element and O-ring.

NOTE:

Make sure that the O-ring is properly seated.

9. Install the oil filter element cover by installing

the bolts, and then tighten them to the speci-
fied torque.

10. Install the oil strainer, compression spring, O-

ring and engine oil drain bolt. Tighten the en-
gine oil drain bolt to the specified torque.

CAUTION:

ECB00320

Before installing the engine oil drain bolt, be
sure to install the O-ring, compression spring
and oil strainer.

11. Add the specified amount of the recommend-

ed engine oil, and then install and tighten the
engine oil filler cap.

1. Oil filter element cover
2. Bolt

3. Oil filter element

4. O-ring

Tightening torque:

Oil filter element cover bolt:

10 Nm (1.0 m·kgf, 7.2 ft·lbf)

Tightening torque:

Engine oil drain bolt:

32 Nm (3.2 m·kgf, 23 ft·lbf)

U5YT64E0.book Page 13 Monday, April 9, 2007 1:03 PM

Содержание YFM35RX







































































































































Результаты поиска

Содержание YFM35RX

Отзывы:

Похожие инструкции для YFM35RX

Бренды по названию

Популярные бренды

Yamaha YFM35RX, Руководство пользователя

Результаты поиска

Содержание YFM35RX

Отзывы:

Похожие инструкции для YFM35RX

Бренды по названию

Популярные бренды