Yamaha YFM35RX страница 41 Скачать руководство пользователя | Manualshive

Страница: 41 / 134

background image

5-3

5

EBU19540

Fuel

Make sure that there is sufficient fuel in the tank.
(See page 4-8.)

WARNING

EWB00520

●

Do not overfill the fuel tank. Fuel expands
when it heats up. If the fuel tank is overfilled,
fuel could spill out due to heat from the en-
gine or the sun.

●

Be careful not to spill fuel, especially on the
engine or exhaust pipe which can cause a
fire and severe injury. Wipe up any spilled
fuel immediately.

●

Do not refuel right after the engine has been
running and is still very hot.

●

Be sure the fuel tank cap is closed securely.

EBU19560

Engine oil

Make sure that the engine oil is at the specified lev-
el. Add oil as necessary. (See page 8-11.)

EBU19710

Front and rear brakes

Brake lever and brake pedal

●

Check that there is no free play in the brake le-
ver. If there is free play, have a Yamaha dealer
check the brake system.

●

Check for correct brake pedal height. (See page
8-25.) If the pedal height is incorrect, have a
Yamaha dealer adjust it.

●

Check the operation of the lever and pedal. They
should move smoothly and there should be a
firm feeling when the brakes are applied. If not,
have a Yamaha dealer check the brake system.

Brake fluid level

Check the brake fluid level. Add fluid if necessary.
(See page 8-23.)

Recommended brake fluid:

DOT 4

U5YT64E0.book Page 3 Monday, April 9, 2007 1:03 PM

«
...
39
40
41
42
43
...
»

Содержание YFM35RX







































































































































Отзывы:

Нет отзывов

Похожие инструкции для YFM35RX

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды