Yamaha YFM35RX Скачать руководство пользователя | Manualshive

Страница: 104 / 134

background image

8-26

8

EBU24710

Adjusting the parking brake free play

The parking brake free play must be checked and,
if necessary, adjusted at the intervals specified in
the periodic maintenance and lubrication chart.
Cable length “A” should measure 64–68 mm
(2.52–2.68 in). Adjust the parking brake free play
as follows.

1. Release the parking brake by moving the

parking brake lever to the right.

2. Fully loosen the locknut and the adjusting bolt

at the rear brake caliper.

3. Loosen the locknut on the brake cable.
4. Turn the adjusting nut on the brake cable in di-

rection (a) to increase the cable length, and in
direction (b) to decrease it.

NOTE:

If the cable length cannot be adjusted to specifica-
tion, consult a Yamaha dealer.

5. Tighten the locknut on the brake cable.
6. Turn in the adjusting bolt at the rear brake cal-

iper until it feels tight, then turn it out 1/8 turn
and tighten its locknut to the specified torque.

1. Locknut
2. Adjusting bolt

3. Cable length “A”

1. Locknut
2. Adjusting nut

U5YT64E0.book Page 26 Monday, April 9, 2007 1:03 PM

«
...
102
103
104
105
106
...
»

Содержание YFM35RX







































































































































Отзывы:

Нет отзывов

Похожие инструкции для YFM35RX

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды