manualshive.com logo in svg

Yamaha YFM35RX, Руководство пользователя

Yamaha YFM35RX - Owner's Manual can be downloaded for free. Пользовательский мануал доступен для скачивания с manualshive.com. Узнайте больше о своем продукте, загрузив мануал сейчас.

Поделиться
Скачать
background image

1-3

1

speed when climbing a hill. If you stall or roll
backwards, follow the special procedure for
braking described in this manual. Dismount on
the uphill side or to a side if pointed straight up-
hill. Turn the ATV around and remount, following
the procedure described in this manual.

●

Always check for obstacles before operating in a
new area.

●

Never attempt to operate over large obstacles,
such as large rocks or fallen trees. Always follow
proper procedures when operating over obsta-
cles as described in this manual.

●

Always be careful when skidding or sliding.
Learn to safely control skidding or sliding by
practicing at low speeds and on level, smooth
terrain. On extremely slippery surfaces, such as
ice, go slowly and be very cautious in order to re-
duce the chance of skidding or sliding out of con-
trol.

●

Never operate an ATV in fast flowing water or in
water deeper than that recommended in this
manual. Remember that wet brakes may have
reduced stopping ability. Test your brakes after
leaving water. If necessary, apply them several
times to let friction dry out the linings.

●

Always be sure there are no obstacles or people
behind you when you operate in reverse. When
it is safe to proceed in reverse, go slowly.

●

Always use the size and type of tires specified in
this manual.

●

Always maintain proper tire pressure as de-
scribed in this manual.

●

Never modify an ATV through improper installa-
tion or use of accessories.

●

Never exceed the stated load capacity for an
ATV. Cargo should be properly distributed and
securely attached. Reduce speed and follow in-
structions in this manual for carrying cargo or
pulling a trailer. Allow greater distance for brak-
ing.

WARNING

EWB00061

●

Always turn off the engine when refueling.

●

Do not refuel right after the engine has been
running and is still very hot.

●

Do not spill gasoline on the engine or ex-
haust pipe/muffler when refueling. Never re-
fuel while smoking, or in the vicinity of
sparks, open flames, or other sources of ig-

U5YT64E0.book  Page 3  Monday, April 9, 2007  1:03 PM

Содержание YFM35RX







































































































































Отзывы:

Нет отзывов

Похожие инструкции для YFM35RX

Бренды по названию

Популярные бренды

Загрузить еще бренды