Yamaha YFM350RZ Скачать руководство пользователя | Manualshive

Страница: 97 / 138

background image

8-18

8

NOTICE:

Make sure that the air filter ele-

ment is properly seated in the air filter
case. Never operate the engine with the air
filter element removed. This will allow un-
filtered air to enter the engine, causing rap-
id engine wear and possible engine
damage. Additionally, operation without
the air filter element will affect carburetor
jetting with subsequent poor performance
and possible engine overheating.

[ECB00461]

13. Install the seat.

TIP

The air filter element should be cleaned every 20–
40 hours. It should be cleaned and lubricated more
often if the ATV is operated in extremely dusty ar-
eas. Each time the air filter element maintenance
is performed, check the air inlet of the air filter case
for obstructions. Check the air filter case rubber
joint to the carburetor fittings and the rubber joint
manifold fittings for an air-tight seal. Tighten all fit-
tings securely to avoid the possibility of unfiltered
air entering the engine.

EBU27701

Cleaning the spark arrester

Select a well-ventilated area free of combustible
materials and make sure the exhaust and muffler
are cool.

1. Remove the bolt.

2. Remove the tailpipe by pulling it out of the

muffler.

3. Tap the tailpipe lightly, and then use a wire

brush to remove any carbon deposits from the
spark arrester portion of the tailpipe and inside
of the tailpipe housing.

1. Bolt

U1BS60E0.book Page 18 Thursday, April 16, 2009 4:11 PM

«
...
95
96
97
98
99
...
»

Содержание YFM350RZ











































































































































Отзывы:

Нет отзывов

Похожие инструкции для YFM350RZ

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды