Yamaha YFM350RZ Скачать руководство пользователя | Manualshive

Страница: 90 / 138

background image

8-11

8

TIP

If a torque wrench is not available when installing
a spark plug, a good estimate of the correct torque
is 1/4–1/2 turn past finger tight. However, the spark
plug should be tightened to the specified torque as
soon as possible.

3. Install the spark plug cap.

EBU2327C

Engine oil and oil filter element

The engine oil level should be checked before
each ride. In addition, the oil must be changed and
the oil filter element cleaned at the intervals speci-
fied in the periodic maintenance and lubrication
chart.

To check the engine oil level

1. Place the ATV on a level surface.
2. Check the engine oil level on a cold engine.

TIP

If the engine was started before checking the oil
level, be sure to warm up the engine sufficiently,
and then wait at least ten minutes until the oil set-
tles for an accurate reading.

3. Remove the engine oil filler cap, and then

wipe the engine oil dipstick off with a clean
rag.

4. Insert the dipstick into the filler hole (without

screwing it in), and then remove it again to
check the oil level.

TIP

The engine oil should be between the minimum
and maximum level marks.

Tightening torque:

Spark plug:

17.5 Nm (1.75 m·kgf, 12.7 ft·lbf)

U1BS60E0.book Page 11 Thursday, April 16, 2009 4:11 PM

«
...
88
89
90
91
92
...
»

Содержание YFM350RZ











































































































































Отзывы:

Нет отзывов

Похожие инструкции для YFM350RZ

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды