Yamaha YFM350RZ Скачать руководство пользователя | Manualshive

Страница: 62 / 138

background image

7-6

7

opening, even when the throttle lever is pushed to
the maximum. Turning in the adjusting screw limits
the maximum engine power available and de-
creases the maximum speed of the ATV. Turning
in the adjusting screw decreases top speed, and
turning it out increases top speed. (See page 4-3.)

Loading and accessories

WARNING

EWB00971

Improper loading or towing can increase the
risk of loss of control, an overturn, or other ac-
cident. To reduce the risk of an accident:

●

Do not exceed the maximum loading limits
for the vehicle (see box in this section or ve-
hicle labeling).

●

Make sure the load does not interfere with
your control or ability to see where you are
going.

●

Reduce speed and allow more room to stop.
A heavier vehicle takes longer to stop.

●

Avoid hills and rough terrain. Choose terrain
carefully. Use extreme caution when towing
or carrying a load on inclines.

●

Turn gradually and go slowly.

As originally equipped, this ATV is not designed to
carry cargo or tow a trailer. If you choose to add ac-
cessories to carry cargo, you must use common
sense and good judgment.
Use extra caution when riding the ATV with addi-
tional loads, such as accessories or cargo. The
ATV’s handling may be adversely affected. Re-
duce your speed when adding additional loads.

1. Adjusting screw

MAXIMUM LOADING LIMIT

ATV loading limit (total weight of cargo, rider,
accessories, and tongue):

100.0 kg (220 lb)

U1BS60E0.book Page 6 Thursday, April 16, 2009 4:11 PM

«
...
60
61
62
63
64
...
»

Содержание YFM350RZ











































































































































Отзывы:

Нет отзывов

Похожие инструкции для YFM350RZ

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды