Yamaha YFM350RZ Скачать руководство пользователя | Manualshive

Страница: 48 / 138

background image

6-1

6

EBU19880

OPERATION

EBU19901

Read the Owner’s Manual carefully before riding
the ATV. If there is a control or function you do not
understand, ask your Yamaha dealer.

WARNING

EWB00631

Read the Owner’s Manual carefully to become
familiar with all controls in order to help pre-
vent any loss of control, which could cause an
accident or injury.

EBU20162

Starting a cold engine

NOTICE

ECB00150

See the “Engine break-in” section on page 6-6
prior to operating the engine for the first time.

1. Set the parking brake.
2. Turn the fuel cock to “ON”.
3. Turn the key to “ON” and the engine stop

switch to “

”.

4. Shift the transmission into neutral. The neutral

indicator light should come on. If the indicator
light does not come on, have a Yamaha deal-
er check the electrical circuit.

TIP

This model is equipped with an ignition circuit cut-
off system. The engine can be started under the
following conditions.

●

The transmission is in neutral.

●

The clutch is disengaged with the shift pedal and
the drive select lever in any position. However, it
is recommended to shift into neutral before start-
ing the engine.

5. Use the starter (choke) in reference to the fig-

ure:

Position (1):

Cold engine start with ambient temperature
below 5 °C (40 °F).

Position (2):

Cold engine start with ambient temperature
between 0 °C (30 °F) and 30 °C (90 °F).

U1BS60E0.book Page 1 Thursday, April 16, 2009 4:11 PM

«
...
46
47
48
49
50
...
»

Содержание YFM350RZ











































































































































Отзывы:

Нет отзывов

Похожие инструкции для YFM350RZ

GRIZZLY 350 YFM35FGB

Бренд: Yamaha Страницы: 142

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды