Yamaha YFM350RZ Скачать руководство пользователя

Страница: 43 / 138

5-2

Rear brake

• Check operation. If soft or spongy, have Yamaha dealer bleed hy-

draulic system.

• Check brake pads for wear, and replace if necessary.
• Check brake fluid level in reservoir, and add recommended brake

fluid to specified level if necessary.

• Check hydraulic system for leakage. Correct if necessary.

5-3, 8-22, 8-23, 8-25

Clutch

• Check operation, and correct if necessary.
• Lubricate cable if necessary.
• Check lever free play, and adjust if necessary.

8-28

Throttle lever

• Make sure that operation is smooth. Lubricate cable and lever hous-

ing if necessary.

• Check cable free play, and adjust if necessary.

5-3, 8-21

Control cables

• Make sure that operation is smooth. Lubricate if necessary.

8-32

Drive chain

• Check chain slack, and adjust if necessary.
• Check chain condition. Lubricate if necessary.

5-4, 8-29, 8-31

Wheels and tires

• Check wheel condition, and replace if damaged.
• Check tire condition and tread depth. Replace if necessary.
• Check air pressure. Correct if necessary.

5-4

Brake and shift pedals

• Make sure that operation is smooth. Lubricate pedal pivoting points

if necessary.

8-33

Brake and clutch levers

• Make sure that operation is smooth. Lubricate lever pivoting points if

necessary.

8-32

Chassis fasteners

• Make sure that all nuts, bolts and screws are properly tightened.

5-6

Instruments, lights and
switches

• Check operation, and correct if necessary.

5-6

ITEM

ROUTINE

PAGE

U1BS60E0.book Page 2 Thursday, April 16, 2009 4:11 PM

Содержание YFM350RZ











































































































































Результаты поиска

Содержание YFM350RZ

Отзывы:

Похожие инструкции для YFM350RZ

Бренды по названию

Популярные бренды

Yamaha YFM350RZ, Руководство пользователя

Результаты поиска

Содержание YFM350RZ

Отзывы:

Похожие инструкции для YFM350RZ

Бренды по названию

Популярные бренды