manualshive.com logo in svg

Yamaha XV19SX(C), Руководство по обслуживанию

Yamaha XV19SX(C) - роскошный мотоцикл с уникальным стилем и мощным двигателем. Для обслуживания и ухода за этим красавцем, скачайте бесплатно Руководство по обслуживанию на manualshive.com. Отличное руководство для любого владельца этого прекрасного мотоцикла.

Поделиться
Скачать
background image

CABLE ROUTING (for XV19S(C)/ XV19M(C)/ XV19CTS(C)/

XV19CTM(C))

2-56

1. EXUP servo motor
2. Fuse box
3. Wire harness
4. Fuel outlet hose
5. Cylinder-#1 right spark plug cap
6. Cylinder-#1 right ignition coil
7. Cylinder-#2 intake air pressure sensor coupler
8. Fuel sender (fuel tank) coupler
9. Meter assembly coupler
10. Throttle cable
11. Front brake hose
12. Cylinder-#2 right spark plug cap
13. Cylinder-#1 left ignition coil
14. Clutch pipe
15. Neutral switch lead
16. Stator coil lead
17. Speed sensor lead
18. O

2

 sensor lead

19. EXUP cable
20. Cylinder-#1 right spark plug lead
21. Cylinder-#1 left spark plug lead
22. ISC (idle speed control) unit inlet hose
23. Cylinder-#2 ISC (idle speed control) unit outlet 

hose

24. Cylinder-#1 ISC (idle speed control) unit outlet 

hose

25. Sub-wire harness 3 coupler
26. Cylinder-#2 right spark plug lead
27. Sub-wire harness 4 coupler
28. Cylinder-#2 left spark plug lead
A. Fasten the cylinder-#1 left and right spark plug 

leads, fuel outlet hose, wire harness and the fuel 
tank damper with the plastic locking tie. Install the 
plastic locking tie in the rear slot of the fuel tank 
damper.

B. Fasten the fuel outlet hose, wire harness, and fuel 

tank damper with the plastic locking tie. Install the 
plastic locking tie in the front slot of the fuel tank 
damper and make sure that the end of the damper 
is aligned with the edge of the flat section on the 
outside of the frame.

C. Fasten the cylinder-#1 left and right ignition coil 

leads, engine temperature sensor lead, and throttle 
position sensor lead to the guide on the engine 
bracket (right upper side) with the plastic locking tie. 
Face the end of the plastic locking tie rearward, and 
then cut off the excess end of the tie.

D. Fasten sub-wire harness 2 with the plastic locking 

tie.

E. Align the positioning tape on the wire harness with 

the top of the frame.

F. 0

–

15 mm (0

–

0.59 in)

G. Route the throttle cables behind the front brake 

hose.

H. Make sure that the wire harness is not twisted 

between the fuel tank and the headlight assembly.

I.

Position the cylinder-#2 left and right spark plug 

leads, sub-wire harness 2 coupler and sub-wire 
harness 4 coupler on top of the guide.

J. Fasten the wire harness and the cylinder-#2 left 

and right spark plug leads with a plastic locking tie, 
making sure to install the tie just past the end of the 
protective tube of the wire harness. Face the end of 
the plastic locking tie inward, and then cut off the 
excess end of the tie.

K. To the throttle position sensor
L. To the fuel injector and engine temperature sensor
M. To the neutral switch
N. To the speed sensor
O. Fasten the stator coil lead with the plastic locking 

ties. Face the end of each plastic locking tie 
outward, and then cut off the excess end of the tie.

P. To the rear brake caliper
Q. Install the O

2

 sensor coupler completely onto the 

O

2

 sensor bracket.

R. Outside of the frame
S. Position the buckle of the plastic locking tie to the 

inside of the frame. Face the end of the plastic 
locking tie upward, and then cut off the excess end 
of the tie.

T. Inside of the frame
U. Position the buckle of the plastic locking tie to the 

inside of the frame.

V. To the wire harness
W. To the cylinder-#2 right spark plug
X. Right side
Y. Position the sub-wire harness 3 coupler and the 

sub-wire harness 4 coupler between the cylinder-
#2 right spark plug lead and the cylinder-#1 ISC 
unit outlet hose.

Z. Face the ends of the hose clamp outward, angled 

45

°

 downward.

AA.Route the cylinder-#2 right spark plug lead under 

the sub-wire harness 4.

AB.Face the ends of the hose clamp downward.
AC.Route the cylinder-#2 left spark plug lead under the 

cylinder-#2 ISC unit outlet hose.

AD.Left side
AE.To the cylinder-#2 left spark plug
AF. Install the clutch pipe onto the clutch release 

cylinder, making sure that the pipe contacts the 
projection on the cylinder.

AG.To the O

2

 sensor

AH.Align the cutout in the clutch pipe union bolt cap 

with the projection on the clutch release cylinder.

Содержание XV19SX(C)















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для XV19SX(C)

hepco & becker TRIUMPH Bonneville T 120 Quick Start Manual preview
TRIUMPH Bonneville T 120
Бренд: hepco & becker Страницы: 4
Honda 08L42-MCA-100 Installation Instructions preview
08L42-MCA-100
Бренд: Honda Страницы: 3
Triumph Bonneville T100 Owner'S Handbook Manual preview
Bonneville T100
Бренд: Triumph Страницы: 198
PEUGEOT 103 LS-U1 Owner'S Manual preview
103 LS-U1
Бренд: PEUGEOT Страницы: 12
Honda C8R600F4 Service Manual preview
C8R600F4
Бренд: Honda Страницы: 362
Fantic XX 125 Use And Maintenance Manual preview
XX 125
Бренд: Fantic Страницы: 153
Shark SX 2 User Manual preview
SX 2
Бренд: Shark Страницы: 28
Rovo Kids Ride-On Motorcycle User Manual preview
Ride-On Motorcycle
Бренд: Rovo Kids Страницы: 17
Hermes LCD 9.13G Manual preview
LCD 9.13G
Бренд: Hermes Страницы: 23
Gemini 953NH User'S And Installer'S Manual preview
953NH
Бренд: Gemini Страницы: 17
Denali HMT.04.10200 Instruction Manual preview
HMT.04.10200
Бренд: Denali Страницы: 2
Atra ATRA10 Quick Start Manual preview
ATRA10
Бренд: Atra Страницы: 3
APRILIA MOJITO 125 Manual preview
MOJITO 125
Бренд: APRILIA Страницы: 576
hepco & becker 700315 Quick Start Manual preview
700315
Бренд: hepco & becker Страницы: 4
KTM 600.12.073.044 Mounting Instructions preview
600.12.073.044
Бренд: KTM Страницы: 13
KTM 400 SUPER COMPETITION 1999 Spare Parts Manual preview
400 SUPER COMPETITION 1999
Бренд: KTM Страницы: 40
KTM 250 SX-F US Owner'S Manual preview
250 SX-F US
Бренд: KTM Страницы: 112
KTM 2014 350 EXC-F SIX DAYS Owner'S Manual preview
2014 350 EXC-F SIX DAYS
Бренд: KTM Страницы: 136

Бренды по названию

Популярные бренды

Загрузить еще бренды