Yamaha XV19SX(C) Скачать руководство пользователя страница 469 | Manualshive

Страница: 469 / 494

Yamaha XV19SX(C) Скачать руководство пользователя страница 469

ELECTRICAL COMPONENTS

7-78

WARNING

EWA13300

Do not quick charge a battery.

CAUTION:

ECA13670

• Never remove the MF battery sealing caps.
• Do not use a high-rate battery charger

since it forces a high-amperage current
into the battery quickly and can cause bat-
tery overheating and battery plate damage.

• If it is impossible to regulate the charging

current on the battery charger, be careful
not to overcharge the battery.

• When charging a battery, be sure to remove

it from the vehicle. (If charging has to be
done with the battery mounted on the vehi-
cle, disconnect the negative battery lead
from the battery terminal.)

• To reduce the chance of sparks, do not

plug in the battery charger until the battery
charger leads are connected to the battery.

• Before removing the battery charger lead

clips from the battery terminals, be sure to
turn off the battery charger.

• Make sure the battery charger lead clips are

in full contact with the battery terminal and
that they are not shorted. A corroded bat-
tery charger lead clip may generate heat in
the contact area and a weak clip spring may
cause sparks.

• If the battery becomes hot to the touch at

any time during the charging process, dis-
connect the battery charger and let the bat-
tery cool before reconnecting it. Hot
batteries can explode!

• As shown in the following illustration, the

open-circuit voltage of an MF battery stabi-
lizes about 30 minutes after charging has
been completed. Therefore, wait 30 min-
utes after charging is completed before
measuring the open-circuit voltage.

▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼ ▼▼▼

▼

▼▼▼

Charging method using a variable-current
(voltage) charger

a. Measure the open-circuit voltage prior to

charging.

NOTE:

Voltage should be measured 30 minutes after
the engine is stopped.

b. Connect a charger and ammeter to the bat-

tery and start charging.

NOTE:

Set the charging voltage at 16–17 V. If the set-
ting is lower, charging will be insufficient. If too
high, the battery will be over-charged.

c. Make sure that the current is higher than the

standard charging current written on the bat-
tery.

NOTE:

If the current is lower than the standard charging
current written on the battery, set the charging
voltage adjust dial at 20–24 V and monitor the
amperage for 3–5 minutes to check the battery.

d. Adjust the voltage so that the current is at the

standard charging level.

e. Set the time according to the charging time

suitable for the open-circuit voltage.

A. Open-circuit voltage (V)
B. Time (minutes)
C. Charging
D. Ambient temperature 20 °C (68 °F)
E. Check the open-circuit voltage.

• Standard charging current is reached

Battery is good.

• Standard charging current is not reached

Replace the battery.

«
...
467
468
469
470
471
...
»

Содержание XV19SX(C)















































































































































































































































































































































































































































































































Отзывы:

Нет отзывов