Yamaha XT660R 2007 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 81

background image

– 10 –

SPEC

CABLE ROUTING

Ê

Place the slack of the left and right front turn sig-
nal light leads between the headlight assembly
and front cowling assembly.

Ë

Fasten the left and right front turn signal light
leads to the headlight stay with a plastic locking
tie, and then cut off the excess end of tie.

Ì

Pass the left and right front turn signal light leads
in front of the headlight stay.

Í

Only the left side is shown in this illustration.
Route the right front turn signal light lead in the
same way.

Î

Pass the left and right front turn signal light leads
between the headlight stay and front fork protec-
tor.

Ï

XT660R

Ð

0 ~ 5 mm (0 ~ 0.20 in) for both left and right
sides

Ñ

XT660X

«
...
14
15
16
17
18
...
»

Содержание XT660R 2007


















































































Отзывы:

Нет отзывов

Похожие инструкции для XT660R 2007

Бренд: hepco & becker Страницы: 4

Mesh Helmet Cover

Бренд: Ops-Core Страницы: 2

Бренд: Sym Страницы: 31

Бренд: Braaap Страницы: 40

Бренд: X-lite Страницы: 96

SEMIFAIRING BATWING SML TOURING

Бренд: PUIG Страницы: 3

KTM390-14-01-SL

Бренд: SRC Страницы: 4

MCL-4000 Series

Бренд: Dakota Digital Страницы: 3

Бренд: hepco & becker Страницы: 7

Бренд: SHERCO Страницы: 102

Бренд: Kabuto Страницы: 20

Бренд: Denali Страницы: 2

Бренд: PIAGGIO Страницы: 275

POCKET BIKE QG-40

Бренд: Coolster Страницы: 13

Бренд: Power Fist Страницы: 20

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 88

Бренд: Yamaha Страницы: 102

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды