Yamaha XT660R 2007 Скачать руководство пользователя страница 41

Страница: 41 / 81

– 35 –

CHAS

REAR WHEEL, BRAKE DISC, AND REAR WHEEL

SPROCKET

EAS00561

REMOVING THE REAR WHEEL (XT660X)

1. Stand the motorcycle on a level surface.

WARNING

Securely support the motorcycle so that
there is no danger of it falling over.

NOTE:

Place the motorcycle on a suitable stand so
that the rear wheel is elevated.

2. Loosen:

• locknut

• adjusting nut

3. Remove:

• stabilizer
• chain cover
• wheel axle nut

• washer
• wheel axle
• rear wheel

NOTE:

Push the rear wheel forward and remove the
drive chain from the rear wheel sprocket.

4. Remove:

• brake caliper

NOTE:

Do not depress the brake pedal when remov-
ing the brake caliper.

EAS00571

INSTALLING THE REAR WHEEL (XT660R)

1. Lubricate:

• wheel axle
• oil seal lips

Recommended lubricant

Lithium-soap-based grease

Содержание XT660R 2007


















































































Результаты поиска

Содержание XT660R 2007

Отзывы:

Похожие инструкции для XT660R 2007

Бренды по названию

Популярные бренды

Yamaha XT660R 2007, Дополнительное руководство по обслуживанию

Результаты поиска

Содержание XT660R 2007

Отзывы:

Похожие инструкции для XT660R 2007

Бренды по названию

Популярные бренды