Yamaha XT660R 2007 Скачать руководство пользователя страница 32

Страница: 32 / 81

– 26 –

CHK

ADJ

ADJUSTING THE DRIVE CHAIN SLACK

EAS00140

CHASSIS

ADJUSTING THE DRIVE CHAIN SLACK

NOTE:

The drive chain slack must be checked at the
tightest point on the chain.

CAUTION:

A drive chain that is too tight will overload
the engine and other vital parts, and one
that is too loose can skip and damage the
swingarm or cause an accident. Therefore,
keep the drive chain slack within the speci-
fied limits.

1. Stand the motorcycle on a level surface.

WARNING

Securely support the motorcycle so that
there is no danger of it falling over.

NOTE:

Place the motorcycle on a suitable stand so
that the rear wheel is elevated.

2. Spin the rear wheel several times and find

the tightest position of the drive chain.

3. Check:

• drive chain slack

Out of specification

→

Adjust.

Drive chain slack

40.0 ~ 55.0 mm (1.57 ~ 2.17 in)

Содержание XT660R 2007


















































































Результаты поиска

Содержание XT660R 2007

Отзывы:

Похожие инструкции для XT660R 2007

Бренды по названию

Популярные бренды

Yamaha XT660R 2007, Дополнительное руководство по обслуживанию

Результаты поиска

Содержание XT660R 2007

Отзывы:

Похожие инструкции для XT660R 2007

Бренды по названию

Популярные бренды