Yamaha VMAX VMX12P Скачать руководство пользователя страница 97

Страница: 97 / 125

PERIODIC MAINTENANCE AND MINOR REPAIR

6-46

5. While supporting the brake cali-

per, pull the wheel axle out.

6. Remove the brake caliper bracket

and spacer.

7. Pull the wheel to the right to sepa-

rate it from the final gear case, and
then remove it.

ECA00062

CAUTION:

Do not push the brake pedal after
the wheel has been removed togeth-
er with the brake disc, otherwise the
brake pads will be forced shut.

EAU03422

To install the rear wheel

1. Apply a light coating of lithium-

soap-based grease to the splines
of the final gear case and wheel
hub.

2. Install the wheel, brake caliper

bracket, spacer and wheel axle.

3. Install the brake caliper by install-

ing the bolts.

NOTE:

Make sure that there is enough space
between the brake pads before install-
ing the brake caliper onto the brake
disc.

4. Install the brake torque rod bolt and

nut at the brake caliper bracket.

5. Install the rear wheel axle nut.
6. Take the motorcycle off the cen-

terstand so that the rear wheel is
on the ground.

7. Tighten the axle nut, brake caliper

bolts, brake torque rod nut, and
pinch bolt to the specified torques.

8. Install the brake torque rod cotter

pin.

EW000124

WARNING

Always use a new cotter pin.

Tightening torques:

Axle nut:

150 Nm (15.0 m·kgf, 108 ft·lb)

Brake caliper bolt:

40 Nm (4.0 m·kgf, 29 ft·lb)

Brake torque rod nut:

23 Nm (2.3 m·kgf, 17 ft·lb)

Rear wheel axle pinch bolt:

16 Nm (1.6 m·kgf, 11 ft·lb)

u5gk12.book Page 46 Wednesday, June 13, 2001 8:55 AM

Содержание VMAX VMX12P






























































































































Результаты поиска

Содержание VMAX VMX12P

Отзывы:

Похожие инструкции для VMAX VMX12P

Бренды по названию

Популярные бренды

Yamaha VMAX VMX12P, Руководство пользователя

Результаты поиска

Содержание VMAX VMX12P

Отзывы:

Похожие инструкции для VMAX VMX12P

Бренды по названию

Популярные бренды